Yamaha 01X Music Mixer User Manual


 
30
Overview of the 01X
01X Owner’s Manual
Before Using Basics Section AppendixGetting Started Reference
Output channel
Stereo output channel
This is a stereo output channel that processes the signals
sent from each channel to the stereo bus. Stereo faders con-
torl the level of these outputs. It provides a 4-band EQ and
dynamics processor identical to those provided on the
input channels. The output signal of the stereo output chan-
nel is sent via the output patch section to the various output
jacks, and is also simultaneously output to the MONITOR
OUT jacks and PHONES jack.
Rec bus output channel
This is a stereo output channel that processes the signals
sent from each channel to the rec bus. It provides a four-
band EQ and dynamics processor identical to those pro-
vided on the input channels. The output signal of the rec
bus channel is sent via the master level/output patch sec-
tion to the various output jacks.
The master level of the rec bus can be controlled by using
the channel 1 fader when [MASTER] layer in the MIXER/
LAYER is seleced in Internal mode.
AUX buses 1 through 4
The signals sent from each channel to AUX buses 1–6 pass
through a master level, and are sent to the output patch sec-
tion.
The master level of AUX buses 1 through 4 can be con-
trolled by using the channel faders 3 through 6 when
[MASTER] layer in the MIXER/LAYER is seleced in
Internal mode.
Getting Started (page 62)
Output patch Reference (page 90)
Output Patch is the section where output signals are
assigned to mLAN channels 1/2 through 23/24, DIGITAL
STEREO OUT jack, and STEREO/AUX OUT jack. The
following output signals can be selected.
Stereo bus (The output signal of the stereo bus routed
through the stereo output channel.)
Rec bus
•AUX bus 1/2
•AUX bus 3/4
In general, these output signals can be assigned to any output jack or
output channel. For the STEREO OUT jacks and DIGITAL STEREO
OUT jacks, two adjacent odd-numbered/even-numbered signals will
always be assigned.
The direct out setting for a specific channel is cancelled if the corre-
sponding output channel is assigned to stereo bus, rec bus or AUX
buses (page 90).
STEREO L
ATT
ATT
INSERT
STEREO (STEREO BUS) L
STEREO (STEREO BUS) R
AUX 1
AUX 2
AUX 3 (FX1)
AUX 4 (FX2)
4BAND EQ
4BAND EQ
DY-
NAMICS
DY-
NAMICS
(Gain Reduction)
LEVEL
ON
BAL
METER
METER
STEREO R
METER
*3
*3 Studio Manager only
RECBUS (BUS) L
RECBUS (BUS) R
STEREO (STEREO BUS) L
STEREO (STEREO BUS) R
AUX 1
AUX 2
AUX 3 (FX1)
AUX 4 (FX2)
RECBUS L
DY-
NAMICS
DY-
NAMICS
(Gain Reduction)
METER
LEVEL
METER
INSERT
RECBUS R
*3 Studio Manager only
METER
*3
AUX1(...4)
AUX 1
AUX 2
AUX 3 (FX1)
AUX 4 (FX2)
LEVEL
METER
-10dBV
L
R
STEREO/AUX OUT
DA
DA
DIGITAL STEREO OUT
COAXIAL
2
mLAN OUT
2
RECBUS
24
*1
DIRECT OUT1-24
*1
24
*1
IEEE 1394
DITHER
STEREO
2
2
RECBUS
2
AUX1/2
2
AUX3/4
STEREO
2
2
RECBUS
2
AUX1/2
2
AUX3/4
SELECT
(OUT PATCH)
2
AUX1/2
2
AUX3/4
STEREO
2
SELECT
(OUT PATCH)
SELECT
(OUT PATCH)
*1 Wordclock 96kHz/88.2kHz : 16