Filter
Top Products
13
4
Status Button: This button has no
function on the AVR480, but is used by
some DVD players and other devices to
access an on-screen menu system.
5
Input Selectors: Pressing one of
these buttons will perform three actions
at the same time. First, if the AVR is not
turned on, this will power up the unit.
Next, it will select the source shown
on the button as the input to the AVR.
Finally, it will change the remote control
so that it controls the compatible product
selected. After pressing one of these but-
tons you must press the
AVR Selector
Button
6
again to operate the AVR’s
functions with the remote.
6
AVR Selector: Pressing this button
will switch the remote so that it will oper-
ate the AVR’s functions. If the AVR is in the
Standby mode, it will also turn the AVR on.
7
Test Tone: Press this button to
begin the sequence used to calibrate the
AVR480’s output levels (see page 22 for
more information on calibrating the
AVR480).
8
Sleep Button: Press this button to
place the unit in the Sleep mode. After
the time shown in the display, the
AVR480 will automatically go into the
Standby mode. Each press of the button
changes the time until turn-off in the fol-
lowing order:
Hold the button pressed for two seconds
to turn off the Sleep mode setting. Note
that this button is also used to change
channels on your TV, VCR and SAT
receiver when selected.
9
Surround Mode Selector: Press
this button to begin the process of chang-
ing the surround mode. After the button
has been pressed, use the
⁄
/
¤
Buttons
C
to select the desired surround mode
(see page 28 for more information).
A
Repeat Button: This button has
no function on the AVR480, but is used
by some CD and DVD players and other
devices to repeat play of program material.
B
Channel Select Button: This button
is used to start the process of setting the
AVR480’s output levels with an external
source. Once this button is pressed, use the
⁄
/
¤
Buttons
C
to select the channel
being adjusted, then press the
Set Button
E
, followed by the
⁄
/
¤
Buttons
C
again, to change the level setting (see page
30 for more information).
C
⁄
/
¤
Buttons: These are naviga-
tional buttons. They will be used most
frequently to select a surround mode.
These buttons are also used to increase or
decrease output levels when configuring
the unit, to select speaker configuration
or to select the digital inputs. They are
also used to enter delay time settings
after the
Delay Button T has been
pressed.
D
‹›
Button: These buttons do not
have a function with the AVR480. When
a DVD player or TV is selected, they may
be used to navigate the menus of those
devices.
E
Set Button: This button is used to
enter settings into the AVR480’s memory.
It is also used in the setup procedures for
delay time, speaker configuration and
channel output level adjustment.
F
Digital Select Button: Press this
button to assign one of the digital inputs
12
to a source. (See page 27 for more
information on using digital inputs.)
G
Numeric Keys: These buttons serve
as a ten-button numeric keypad to enter
tuner preset positions. They are also used
to select channel numbers when a TV,
VCR or Sat receiver has been selected as
the input source, or to select track numbers
on a compatible CD, DVD or LD player.
H
Tuner Mode: Press this button when
the tuner is in use to select between
automatic tuning and manual tuning.
When the button is pressed so that the
AUTO Indicator
M
goes out, pressing
the
Tuning Buttons
J
8
will move
the frequency up or down in single-step
increments. When the FM band is in
use and the
AUTO Indicator
M
is on,
pressing this button will change to
monaural reception, making even weak
stations audible (see page 31 for more
information).
I
Direct Button: In Tuner mode, press
this button when the tuner is in use to
start the sequence for direct entry of a
station’s frequency. After pressing the
button, simply press the proper
Numeric
Keys
G
to select a station (see page
31 for more information on the tuner).
J
Tuning Up/Down: When the tuner is
in use, these buttons will tune up or down
through the selected frequency band. If the
Tuner Mode Button
H
@
has been
pressed so that the
AUTO Indicator
M
is lit, pressing either of the buttons will
cause the tuner to seek the next station
with acceptable signal strength for quality
reception. When the
AUTO Indicator
M
is NOT illuminated, pressing these buttons
will tune stations in single-step increments
(see page 31 for more information).
K
Night Mode: Press this button to
activate the Night mode. This mode is
available only with Dolby Digital-encoded
digital sources, and it preserves dialogue
(center channel) intelligibility at low vol-
ume levels (see page 29 for more
information).
L
Subtitle On/Off Button: This button
has no function on the AVR480, but is
used by some DVD players and other
devices to turn on or off on-screen
subtitles.
M
Transport Controls: These buttons
do not have any functions for the AVR,
but they may be used for the forward/
reverse play operation of a wide variety
of compatible CD or DVD players, and
audio or videocassette recorders.
N
Track Skip Up/Down Buttons:
These buttons have no direct function
with the AVR480, but when used with a
compatibly programmed CD or DVD player,
they will change the track or chapter of
the disc currently being played.
90
min
80
min
70
min
60
min
50
min
40
min
30
min
20
min
10
min
OFF