Filter
Top Products
64
Parameter list
PATCH COMMON parameters
Parameter
Value Explanation Panel operation
PATCH
NAME
(Up to 12 characters) You can assign a name to the patch.
Available characters/symbols:
space, A–Z, a–z, 0–9, ! “ # $ % & ‘ ( ) * + , - . / : ; < = >
? @ [ \ ] ^ _ ` { | }
–
PATCH
LEVEL
0–127 Specifies the volume of the patch. Hold down the CANCEL button and
turn the FX DEPTH knob
TONE
BALANCE
-63 (LOWER)–
+63 (UPPER)
Adjusts the volume balance of the UPPER tone and the
LOWER tone.
Hold down the CANCEL button and
turn the MIX/MOD BALANCE knob
PATCH
TEMPO
5–300 (BPM) This is the tempo value stored for each patch.
This will be the tempo of the arpeggio, and the refer-
ence tempo used when you specify the LFO cycle in
terms of a note length (TEMPO SYNC, p. 62).
Use the TEMPO buttons, or press the
TAP button three or more times at quar-
ter-note intervals of the desired timing
(p. 22, p. 26)
KEYBOARD
KEYBOARD
MODE
SINGLE, DUAL,
SPLIT
SINGLE:
Either the UPPER tone or the LOWER tone
(not both) will sound.
DUAL:
The UPPER tone and the LOWER tone will
sound together (p. 46).
SPLIT:
The keyboard will be split into two regions that
play the UPPER and LOWER tone separately (p. 47).
Press the DUAL/SPLIT button (p. 46)
KEYBOARD
PART
UPPER, LOWER Specifies which tone will be played from the keyboard
when KEYBOARD MODE is “SINGLE.”
Press the UPPER/LOWER buttons (p.
46)
SPLIT
POINT
A0–C8 Specifies the note (key) at which the keyboard will be
split when KEYBOARD MODE is “SPLIT.”
1.
Hold down the CANCEL button and
press the TAP button
2.
Hold down the DUAL/SPLIT button
and press a key (p. 71)
3.
Press the CANCEL button
POLY/SOLO
LOWER
SOLO+LEGATO,
SOLO, POLY
Turns solo and legato (p. 19) on/off for the LOWER tone.
SOLO+LEGATO:
Solo and legato will both be on.
SOLO:
Only solo will be on.
POLY:
Both solo and legato will be off.
Press the SOLO button (p. 19)
UPPER SOLO+LEGATO,
SOLO, POLY
Turns solo and legato (p. 19) on/off for the UPPER tone. Press the SOLO button (p. 19)
PITCH BEND RANGE
LOWER
0–24 Specifies the amount of pitch change that will occur for
the LOWER tone when the pitch bend lever (p. 18) is
moved all the way to left or right.
This is specified in semitone steps. The maximum
range is 24 semitones (2 octaves).
1.
Hold down the CANCEL button and
press the TAP button
2.
Hold down the LOWER button and
press a key (C2–C4, p. 71)
3.
Press the CANCEL button
UPPER 0–24 Specifies the amount of pitch change that will occur for
the UPPER tone when the pitch bend lever (p. 18) is
moved all the way to left or right.
This is specified in semitone steps. The maximum
range is 24 semitones (2 octaves).
1.
Hold down the CANCEL button and
press the TAP button
2.
Hold down the UPPER button and
press a key (C2–C4, p. 71)
3.
Press the CANCEL button
OCTAVE SHIFT
LOWER
-3– +3 Shifts the range of the LOWER tone up or down in steps
of one octave.
Hold down the LOWER button and
press the OCT UP/DOWN buttons
UPPER -3– +3 Shifts the range of the UPPER tone up or down in steps
of one octave.
Hold down the UPPER button and press
the OCT UP/DOWN buttons
PORTAMENTO
LOWER
OFF, ON Turns portamento (p. 19) on/off for the LOWER tone. Press the LOWER button, and then
press the PORTAMENTO button (p. 19)
TIME 0–127 Specifies the time over which portamento is to change
the pitch of the LOWER tone.
Higher values will produce a longer (slower) transi-
tion to the pitch of the next note.
Press the LOWER button, then hold
down the PORTAMENTO button and
press a NUMBER button (1–8) or turn
the TIME knob (p. 19)
UPPER OFF, ON Turns portamento (p. 19) on/off for the UPPER tone Press the UPPER button, and then press
the PORTAMENTO button (p. 19)
TIME 0–127 Specifies the time over which portamento is to change
the pitch of the UPPER tone.
Higher values will produce a longer (slower) transi-
tion to the pitch of the next note.
Press the UPPER button, then hold
down the PORTAMENTO button and
press a NUMBER button (1–8) or turn
the TIME knob(p. 19)
SH-201_r_e.book 64 ページ ２００６年４月２７日 木曜日 午前１１時２８分