Filter
Top Products
68
Parameter list
These are settings that apply to the entire SH-201.
MIDI parameters
SYSTEM COMMON parameters
Parameter
Value Explanation Panel operation
MASTER LEVEL
0–127 Determines the overall volume of the SH-
201.
–
MASTER TUNE 415.30–
466.20 (Hz)
Tunes the entire SH-201. Specified in terms
of the frequency of the A4 key.
Hold down the CANCEL button and turn the PITCH knob
MASTER KEY
SHIFT
-24– +24 Shifts the pitch of the entire SH-201 upward
or downward in semitone steps.
–
PATCH
REMAIN
OFF, ON If this is “ON,” the sound of the currently
sounding patch will be maintained when
you select a different patch.
1.
Hold down the CANCEL button and press the TAP button
2.
Press the PRESET button and then press the BANK D button
3.
Press the NUMBER 1 button
Lit:
ON,
Dark:
OFF
4.
Press the CANCEL button
CLOCK
SOURCE
PATCH,
SYSTEM,
MIDI, USB
Selects the synchronization source for the
arpeggiator/recorder tempo.
PATCH:
Synchronize to the tempo saved
in each patch (PATCH TEMPO, p. 64).
SYSTEM:
Synchronize to the tempo that
is common to the entire SH-201 system
(SYSTEM TEMPO).
MIDI:
Synchronize to MIDI messages re-
ceived via the MIDI IN connector.
USB:
Synchronize to MIDI messages re-
ceived via the USB connector.
1.
Hold down the CANCEL button and press the TAP button
2.
Press the PRESET button and then press the BANK B button
3.
Press a NUMBER button (1–4)
1:
PATCH,
2:
SYSTEM,
3:
MIDI,
4:
USB
4.
Press the CANCEL button
* Don’t set this to “MIDI” or “USB” unless you need to syn-
chronize the SH-201 to the MIDI clock from an external de-
vice. With these settings, the arpeggiator, recorder, tempo-
synchronized LFO, etc., will not work correctly.
SYSTEM
TEMPO
5–300
(BPM)
This is the common tempo value used by the
entire SH-201 when the CLOCK SOURCE
parameter (see above) is set to “SYSTEM.”
With the CLOCK SOURCE parameter set to “SYSTEM,” press
the TEMPO buttons or press the TAP button three or more
times at quarter-note intervals of the desired tempo (p. 22, p.
26).
Parameter
Value Explanation Panel operation
RX/TX CHANNEL
1–16 Specifies the MIDI channel on which the SH-201 will
transmit and receive MIDI messages.
1.
Hold down the CANCEL button and
press the TAP button
2.
Press the PRESET button and then press
the BANK A button
3.
Press a NUMBER button (1–8)
1–8 (Lit in red):
1–8
1–8 (Lit in green):
9–16
4.
Press the CANCEL button
MIDI-USB THRU OFF, ON If this is “ON,” MIDI messages received at the MIDI IN
connector will be re-transmitted without change from
the USB connector.
1.
Hold down the CANCEL button and
press the TAP button
2.
Press the PRESET button and then press
the BANK C button
3.
Press a NUMBER button (1, 2)
1:
MIDI-USB THRU
2:
SOFT THRU
Lit:
ON,
Dark:
OFF
4.
Press the CANCEL button
SOFT THRU OFF, ON If this is “ON,” MIDI messages received at the MIDI IN
connector will be re-transmitted without change from
the MIDI OUT connector.
RECEIVE SWITCH
PROGRAM
CHANGE
OFF, ON If this is “ON,” the patch number or the patch bank (A–
D) will change when a program change message is re-
ceived.
1.
Hold down the CANCEL button and
press the TAP button
2.
Press the PRESET button and then press
the BANK C button
3.
Press a NUMBER button (3, 4)
3:
PROGRAM CHANGE
4:
BANK SELECT
Lit:
ON,
Dark:
OFF
4.
Press the CANCEL button
BANK SELECT OFF, ON If this is “ON,” the patch group (PRESET/USER) will
change when a MIDI bank select message is received.
SH-201_r_e.book 68 ページ ２００６年４月２７日 木曜日 午前１１時２８分