Filter
Top Products
ZOOM G7.1ut
34
Using the Function Foot Switch
The G7.1ut provides a programmable [FUNCTION] (CH A/B) foot switch on the top panel. You can select
one from a range of functions, assign it to the switch, and store the setting for each patch individually.
1. In play mode, select the patch.
HINT
The [FUNCTION] (CH A/B) foot switch assignment
can be set separately for each patch.
2. Press the [TOTAL/FUNCTION] effect
module key.
The [FUNCTION] (CH A/B) foot switch
assignment is part of the [TOTAL/FUNCTION]
module.
The display changes as follows.
3. Turn parameter knob 2 to select the
function to be assigned to the
[FUNCTION] (CH A/B) foot switch.
When you turn parameter knob 2, the display
changes as follows.
The following functions can be assigned to the
[FUNCTION] (CH A/B) foot switch.
● PRE-AMP CH A/B
The [FUNCTION] (CH A/B) foot switch
toggles between the pre-amp channels A and B.
● BPM TAP
The [FUNCTION] (CH A/B) foot switch can
be used to specify the individual tempo for a
patch (→ p. 35). When the switch is pressed
repeatedly, the interval between the last two
presses is taken as the new tempo setting
.
HINT
Using the tempo set here, specific parameters
(Time and Rate) can be synchronized in note units
(
→ p. 35).
● Delay TAP
The [FUNCTION] (CH A/B) foot switch can
be used to specify the Time parameter for the
DELAY module.
HINT
• While BPM TAP specifies the tempo for an
individual patch, DELAY TAP uses the foot
switch operation interval to directly set the Time
parameter value (delay time).
• To use Delay TAP, the DELAY module must be
active for that patch.
● Hold Delay
The [FUNCTION] (CH A/B) foot switch
toggles hold delay between on and off. When
you press the [FUNCTION] (CH A/B) foot
switch in a patch for which hold delay is active,
the hold function is turned on and the current
delay sound is repeated. Pressing the
[FUNCTION] (CH A/B) foot switch once more
cancels hold, and the delay sound will decay
naturally (see illustration on next page).
HINT
To use Hold Delay, the DELAY module must be
active for that patch.
● Delay Mute
The [FUNCTION] (CH A/B) foot switch
toggles DELAY module input muting between
on and off.
¡
¡
BPM =120
BPM =120
TOTAL:Tempo
TOTAL:Tempo
™PRE-AMP CH A/B
PRE-AMP CH A/B
é
TOTAL:Function
TOTAL:Function
[FUNCTION] (CH A/B) foot switch
assignment
Using the Function Foot Switch
ZOOM G7.1ut
35
[FUNCTION] (CH A/B)
foot switch pressed
Switch pressed again
Original
sound
Delay sound
Hold
● Bypass OnOff, Mute OnOff
The [FUNCTION] (CH A/B) foot switch toggles the
bypass mode or mute mode between on and off.
When either mode is activated, the tuner display
comes up.
●
Manual Mode
The [FUNCTION] (CH A/B) foot switch
toggles between play mode and manual mode.
● COMP OnOff, WAH/EFX1 OnOff, ZNR
OnOff, PRE-AMP OnOff, EQ OnOff,
MOD/EFX2 OnOff, DELAY OnOff,
REVERB OnOff
The [FUNCTION] (CH A/B) foot switch
toggles the respective module between on and
off.
HINT
When you select “PRE-AMP CH A/B”, the LED of
the [FUNCTION] (CH A/B) foot switch lights up in
red (A) or green (B). When you select “BPM TAP”
or “Delay TAP”, the LED flashes orange in sync
with the BPM setting. When other functions are
selected, the LED is lit in orange.
4. After selecting a function to assign to
the [FUNCTION] (CH A/B) foot switch,
press the [EXIT] key.
The unit returns to play mode.
NOTE
Any changes in assignment settings will be lost
when you select a new patch. Be sure to store the
patch if you want to keep the changes (
→ p. 27).
When you next call up the stored patch, the
[FUNCTION] (CH A/B) foot switch will control
the selected function.
Specifying the tempo for a
patch
The G7.1ut lets you specify a tempo for each
individual patch and synchronize specific
parameters to this tempo in note units. This
section explains how to specify and use the tempo
setting for a patch.
1. In play mode, select the patch.
2. Press the [TOTAL/FUNCTION] effect
module key.
The tempo setting for each patch is part of the
[TOTAL/FUNCTION] module.
When you press the [TOTAL/FUNCTION] effect
module key, the current tempo setting appears on
the display.
3. Turn parameter knob 1 to set the
tempo.
The tempo setting range is 40 – 250.
¡
¡
BPM =120
BPM =120
TOTAL:Tempo
TOTAL:Tempo