Filter
Top Products
Linking Effects
ZOOM G7.1ut
52
Using the Amp Select
Function
The G7.1ut incorporates an Amp Select function
that optimizes the frequency response to match a
the type of amplifier in use. When starting to use
the G7.1ut or when changing the guitar amp, you
should choose a suitable Amp Select setting as
described below.
NOTE
The Amp Select feature is disabled for patches
where the CABINET module is set to on. This is
because the PRE-AMP module algorithm for direct
recording will be automatically selected when the
CABINET module is on.
1. In play mode, press the [AMP
SELECT/SYSTEM] key.
2. Turn parameter knob 1 to select one
of the following settings.
● FRONT
This is the standard setting for using the
GUITAR INPUT on the front of the guitar
amp.
● COMBO R1
This setting is suitable when using the POWER
INPUT on the rear panel of a Roland JC-120
guitar amp.
● COMBO R2
This setting is suitable when using the POWER
INPUT on the rear panel of a Fender combo
amp.
● STACK R
This setting is suitable when using the POWER
INPUT on the rear panel of a Marshall stack
amp.
3. When the setting is complete, press
the [EXIT] key.
The indication "Store...?" appears on the display,
to allow you to store the changes.
4. Press the [STORE/SWAP] key to save
the changes.
In the above condition (while "Store...?" is
shown), only the [STORE/SWAP], [EXIT], and
[PAGE] keysp are active. By pressing the [EXIT]
key, you can abort the changes and return to play
mode without saving.
Changing the insert position
of the pre-amp section and
WAH/EFX1 module
The G7.1ut allows you to change the insert
position of the four modules making up the pre-
amp section (ZNR, PRE-AMP, EQ, CABINET)
and the WAH/EFX1 module. This will result in
changes to the effect action and tone.
■ Changing the insert position of
the WAH/EFX1 module
To change the insert position of the WAH/EFX1
module, call up the Position parameter and set it
to “Befr” (before pre-amp section) or “Aftr” (after
pre-amp section). The Position parameter can be
used when the Booster, Tremolo, or Octave effect
type is not selected.
1. In play mode, manual mode, or edit
mode, press the [WAH/EFX1] key.
2. Turn the [TYPE] knob and select an
effect type other than Booster,
Tremolo, or Octave.
¡FRONT
FRONT
AMP Select 1/26
AMP Select 1/26
Linking Effects
ZOOM G7.1ut
53
EQPRE-AMPZNR
Fig. 1 Pre-amp section = PRE, WAH/EFX1 = Befr
Fig. 2 Pre-amp section = PRE, WAH/EFX1 = Aftr
Fig. 3 Pre-amp section = POST, WAH/EFX1 = Befr
Fig. 4 Pre-amp section = POST, WAH/EFX1 = Aftr
Pre-amp section
COMP WAH/EFX1 MOD/EFX2
CABINET
DELAY REVERB
EQPRE-AMPZNR
Pre-amp section
COMP WAH/EFX1 MOD/EFX2
CABINET
DELAY REVERB
EQPRE-AMPZNR
Pre-amp section
COMP WAH/EFX1 MOD/EFX2
CABINET
DELAY REVERB
EQPRE-AMPZNR
Pre-amp section
COMP WAH/EFX1MOD/EFX2
CABINET
DELAY REVERB
3. Turn parameter knob 1 to select
“Befr” (before pre-amp section) or
“Aftr” (after pre-amp section).
4. When the setting is complete, press
the [EXIT] key.
The unit returns to the previous mode. To enable
the changed setting, be sure to store the patch (→
p. 27).
■ Changing the insert position of
the pre-amp section
To change the insert position of the pre-amp
section, call up the Chain parameter and set it to
“Pre” (before MOD/EFX2 module) or “Post”
(after DELAY module). The Chain parameter can
be used with all effect types of the PRE-AMP
module.
1. In play mode, manual mode, or edit
mode, press the [PRE-AMP] key.
The display changes as follows.
2. Turn parameter knob 2 to select “Pre”
(before MOD/EFX2 module) or “Post”
(after DELAY module).
3. When the setting is complete, press
the [EXIT] key.
The unit returns to the previous mode. To enable
the changed setting, be sure to store the patch (→
p. 27).
NOTE
• When the “Pre” setting is selected as pre-amp
section insert position, the signal after the MOD/
EFX2 module is processed entirely in stereo.
When you select “Post”, the signal is processed
in the pre-amp section in mono.
• The pre-amp section insert position applies to
both the A and B channel. Choosing a different
setting for the two channels is not possible.
The module lineup with different settings for the
WAH/EFX1 module and pre-amp section
insertion position is shown below.
Post
Post
–œ–œµµ
–œ–œµµ
Chain
Chain
œ–ø–––
œ–ø–––
Parameter nameParameter value