Filter
Top Products
SK-96370-144PMC-GDC User Guide
Chapter 2 Installation
© Fujitsu Microelectronics Europe GmbH - 11 - FMEMCU-UG-960014-10
2.2 Default Jumper settings for MB96370 Series
The following table lists all jumpers including its default setting and location on the starterkit.
Jumper Description / Function Type
Default
Setting
Coordinates
JP1 X1A Jumper 3 pin 1-2 J 10
JP2 X0A Jumper 4 pin 1-2 J 10
JP3 Switch SW1 : INT0/NMI Jumper 2 pin Closed G 6
JP4 Switch SW2 : INT5 Jumper 2 pin Closed G 6
JP5 Switch SW3 : TIN1 Jumper 2 pin Closed H 6
JP6 Switch SW4 : IN0 / TTG4/0 Jumper 2 pin Closed H 6
JP7 Switch SW5 : IN1 / TTG5/1 Jumper 2 pin Closed H 6
JP8 C pin Jumper 2 pin Closed I 14
JP9 SDA0 pull-up Jumper 2 pin Open G 15
JP10 SCL0 pull-up Jumper 2 pin Open G 15
JP11 AVCC Jumper 2 pin Closed J 16
JP12 AVRH Jumper 2 pin Closed J 15
JP13 AVRL Jumper 2 pin Closed J 15
JP14 AVSS Jumper 2 pin Closed K 15
JP15
Voltage selection for MCUVCC
(3.3V only for SK-96370-144PMC-GDC with extern. memory)
Jumper 3 pin
2-3
Do not change!
J 17
JP16 MCUVCC Jumper 2 pin Closed K 17
JP17 DVCC Jumper 3 pin 2-3 L 12
JP18 DVSS Jumper 2 pin Closed L 10
JP19 UART0 : CTS / RTS Jumper 2 pin Closed I 3
JP20 CAN0 Transceiver type Solder JP 3 pin 1-2 D 4
JP21 SIN0 : RS232 / LIN transceiver Jumper 3 pin 1-2 H 5
JP22 Mains Switch Jumper 2 pin Open L 17
JP23 UART0 : DTR / RTS Jumper 3 pin Open H 3
JP24 CAN0 RxD Jumper 2 pin Closed D 4
JP25 SOT0 : RS232 / LIN transceiver Jumper 3 pin 1-2 I 5
JP26 CAN0 TxD Jumper 2 pin Closed D 3
JP27 UART0 : RS232 / LIN Jumper 3 pin 1-2 I 3
JP28 UART0 : LIN VBat Jumper 2 pin Open H 3
JP29 UART0 : LIN-Enable Jumper 2 pin Open I 3
JP30 LIN0 Transceiver type Solder JP 3 pin 1-2 I 5
JP31 UART0 : LIN Master Jumper 2 pin Open J 3
JP32 CAN1 Transceiver type Solder JP 3 pin 1-2 G 4
JP33 Reset by UART 0 / 2 Jumper 3 pin Open J 5
JP34 CAN1 RxD Jumper 2 pin Closed G 4
JP35 CAN1 TxD Jumper 2 pin Closed G 3
JP36 UART2 : CTS / RTS Jumper 2 pin Closed K 3
JP37 SIN2 : RS232 / LIN Jumper 3 pin 1-2 K 5
JP38 UART2 : DTR / RTS Jumper 3 pin Open K 3
JP39 SOT2 : RS232 / LIN Jumper 3 pin 1-2 K 5
JP40 UART2 : RS232 / LIN Jumper 3 pin 1-2 K 3
JP41 UART Reset / Inverter Jumper 3 pin Open J 7