Filter
Top Products
Parameters
26
Group 4: Amp
Amp Type [Type 1, Type 2, Pre Amp]
here you can select the amp type.
Type 1: This is a conventional organ power amp. It
produces a mild and fat sound.
Type 2: Compared to Type 1, this emphasizes the high
range, and produces a more uncolored sound.
Pre Amp: Use a pre amp. This is the sound of the organ's
line-out.
When Type 1 or Type 2 are selected: When the front
panel ROTARY [ON] key is used to turn on the
rotary speaker, the effect of the rotary speaker will be
simulated. When this is turned off, a conventional
speaker will be simulated.
When Pre Amp is selected: The power amp and
rotary speaker will not be used, and the sound will
be as if it were taken from the preamp line-out of the
organ itself.
Spkr Simulator (Speaker Simulator) [On, Off]
When the “Amp Type” parameter is set to Type 1 or Type
2, this turns the amp simulator function on or off.
Amp Gain [0...99]
Adjusts the gain (amplification) when the “Amp Type”
parameter is set to Type 1 or Type 2.
With high settings of this value, the sound will distort
more severely when the expression/overdrive is raised.
This setting will not apply if the “Amp Type”
parameter is set to Pre Amp.
Tone Treble [-10...+10]
Adjusts the high frequency level of the amp selected by
the “Amp Type” parameter.
Tone Middle [-10...+10]
Adjusts the mid-frequency level of the amp selected by
the “Amp Type” parameter.
Tone Bass [-10...+10]
Adjusts the low frequency level of the amp selected by
the “Amp Type” parameter.
Group 4: Tone Trebel
Tone Middle
Tone Bass
Amp Type: Pre Amp
Pre Amp
Reverb
Group 4: Amp Gain
Tone Trebel
Tone Middle
Tone Bass
Amp Type: Amp 1 or Amp 2
Amp 1
or
Amp 2
Rotary
Pre Amp
Reverb
Group 5: Rev Routing
Speaker
Group 4: Spkr Simulator
Group 5: Reverb
Reverb Type [Room, Hall, Plate, Dark]
Selects the type of reverb.
Reverb Time [00.25...16.00 (Sec)]
Specifies the reverb time.
The range in which the reverb time can be adjusted
will depend on your selection for the “Reverb Type”
parameter.
Reverb Mix Level [0...99]
Specifies the amount of reverb signal that is mixed with
the original sound.
Rev Routing (Reverb Routing) [Rot->Rev, Rev->Rot]
Selects whether the reverb will be applied before the
rotary speaker or after it.
Rot->Rev: Reverb will be applied after the rotary speaker.
Rev->Rot: Reverb will be applied before the rotary
speaker.
This setting will not be used if the “Amp Type”
parameter is set to Pre Amp.
Group 6: Rotary Effect
These settings will not be used if the “Amp Type”
parameter is set to Pre Amp.
Horn: 0 Rotor: 100 (Rotary Horn/Rotor Balance)
[0:100...100:0]
Adjuststhe volume balance between the horn and rotor of
the rotary speaker.
Horn Slow Speed [0...99]
Specifies the rotational speed of the horn during slow
rotation.
Horn Fast Speed [0...99]
Specifies the rotational speed of the horn during fast
rotation.
Rotor Slow Speed [0...99]
Specifies the rotational speed of the rotor during slow
rotation.
Rotor Fast Speed [0...99]
Specifies the rotational speed of the rotor during fast
rotation.
Horn Up Transit (Horn Up Transition) [0...99]
Specifies the time over which the horn will change from
slow to fast rotation.
Horn Down Transit (Horn Down Transition) [0...99]
Specifies the time over which the horn will change from
fast to slow rotation.
Horn Stop Transit (Horn Stop Transition) [0...99]
Specifies the time it will take for the horn to actually come
to rest after rotation is switched off.
Horn Strt Transit (Horn Start Transition) [0...99]
Specifies the time it will take for the horn to reach the
specified speed after rotation is switched on.