Filter
Top Products
Parameters
28
* (Pdl 1), (Pdl 2): These indicate that Pedal 1 or Pedal 2 are selected for the Global mode Group 1 “Prog Up Ctrl” or “Prog Down Ctrl” parameters. With these settings, the settings of
Global mode are used, and the settings you made here will be ignored. However if you select another value in Global mode, the display here will change from (Pdl 1) to Pedal 1 or
from (Pdl 2) to Pedal 2, and you will be able to operate the corresponding function from the pedal switch.
Hold Uppr Ctrl (Hold Upper Controller)
[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]
This is displayed in Normal Edit mode.
Pedal 1: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 1 jack will switch Hold on/off
for the notes played on the keyboard that controls the
UPPER tone generator.
Pedal 2: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 2 jack will perform the above
operation.
Off: No function.
Hold Lowr Ctrl (Hold Lower Controller)
[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]
This is displayed in Normal Edit mode.
Pedal 1: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 1 jack will switch Hold on/off
for the notes played on the keyboard that controls the
LOWER tone generator.
Pedal 2: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 2 jack will perform the above
operation.
Off: No function.
Wheel Brk Ctrl (Wheel Brake Controller)
[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]
This is displayed in Normal Edit mode.
Pedal 1: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 1 jack will switch the “Wheel
Brake” parameter (Global mode Group 7) on/off.
Pedal 2: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 2 jack will perform the above
operation.
Off: No function.
Wheel Brk Pedal (Wheel Brake Pedal Mode)
[Momnt, Alter]
Select the on/off operation of the pedal switch etc.
connected to the rear panel ASSIGNABLE PEDAL/SW 1
or 2 jack.
Momnt: The pitch will gradually fall as long as you
continue pressing the pedal switch. When you release the
pedal switch, the pitch will gradually rise to the normal
state.
Alter: The pitch will begin falling once you press the
pedal switch. When you press it once again, the pitch will
gradually rise to the normal state.
Rtry FAST Ctrl (Rotary FAST Controller)
[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]
Pedal 1: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 1 jack will turn the ROTARY
[FAST] key on/off.
Pedal 2: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 2 jack will perform the above
operation.
Off: No function.
Rtry FAST Pedal (Rotary FAST Pedal Mode)
[Momnt, Alter]
Select the on/off operation of the pedal switch etc.
connected to the rear panel ASSIGNABLE PEDAL/SW 1
or 2 jack. The pedal switch will have the same function as
pressing the front panel ROTARY [FAST] key.
Momnt: The rotary speed will gradually increase as long
as you continue pressing the pedal switch, until it reaches
the speed specified by the Group 6 “Rotor Fast Speed”
parameter. When you release the pedal switch, the rotary
speed will gradually decrease until it reaches the speed
specified by the Group 6 “Rotor Slow Speed” parameter.
Alter: Once you press the pedal switch, the rotary speed
will gradually increase until it reaches the speed specified
by the Group 6 “Rotor Fast Speed” parameter. When you
press the pedal switch once again, the rotary speed will
gradually decrease until it reaches the speed specified by
the Group 6 “Rotor Slow Speed” parameter.
Rtry STOP Ctrl (Rotary STOP Controller)
[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]
Pedal 1: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 1 jack will turn the ROTARY
[STOP] key on/off.
Pedal 2: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 2 jack will perform the above
operation.
Off: No function.
Rtry STOP Pedal (Rotary STOP Pedal Mode)
[Momnt, Alter]
Select the on/off operation of the pedal switch etc.
connected to the rear panel ASSIGNABLE PEDAL/SW 1
or 2 jack. The pedal switch will have the same function as
pressing the front panel ROTARY [STOP] key.
Momnt: The rotary speed will gradually slow down and
then stop as long as you continue pressing the pedal
switch.
Alter: Once you press the pedal switch, the rotary speed
will gradually slow down and then stop.
Amp Gain Ctrl (Amp Gain Controller)
[Off, Pedal 1/(Pdl 1)*, Pedal 2/(Pdl 2)*]
Pedal 1: An expression pedal etc. connected to the rear
panel ASSIGNABLE PEDAL/SW 1 jack will control the
Group 4 “Amp Gain” parameter of Normal Edit mode
and EX Edit mode.
Pedal 2: An expression pedal etc. connected to the rear
panel ASSIGNABLE PEDAL/SW 2 jack will perform the
above operation.
Off: No function.