Filter
Top Products
28
Using Effects
Here’s how to apply reverb to the sound of each group.
1
Press the [1-8] or [9-16] button to select the layer whose
reverb you want to adjust.
2
Press the [REVERB] button.
The [REVERB] button will light, and reverb will turn on.
* Reverb will turn off if you press the [REVERB] button once again.
3
Press the [REVERB SEND] button.
The [REVERB SEND] button will light; now you can use the [Control]
knobs to adjust the reverb send.
4
Turn the [Control] knobs of the groups to which you want
to apply reverb, adjusting their reverb send.
* The indicators around the [Control] knobs indicate the
approximate reverb send value.
When the 6 o’clock indicator is lit, the reverb send
is at the “0.0 dB” setting.
1
Press the [REVERB SEND] button.
2
While holding down the [REVERB SEND] button, press the
button for the group (see table below) whose reverb send
you want to return to its initial setting.
The reverb send of the selected group will be set to its initial setting,
and will be set to “-Inf dB.”
* This operation cannot be executed if Store mode (p. 30) or Recall
mode (p. 31) are on.
Here’s how to apply EQ to the sound of each group.
1
Press the [1-8] or [9-16] button to select the layer whose
EQ you want to adjust.
2
Press the button for the EQ setting that you want to
adjust (see table below).
The selected button will light; now you can use the [Control] knobs
to adjust the EQ parameters.
3
Turn the [Control] knob of the desired group to adjust its
EQ parameter.
* The indicators around the [Control] knobs indicate the
approximate value of the EQ parameter.
When the 6 o’clock indicator is lit, the gain is at
“0.0 dB.”
1
Press the button of the EQ parameter that you want to
reset to its initial value (see table below).
The following table shows the button for each EQ parameter and its
initial value.
2
While holding down the button you selected in step 1,
press the button for the group(s) whose setting you want
to return to the initial value (see table below).
The EQ parameter of the selected group will return to its initial value.
* This operation cannot be executed if Store mode (p. 30) or Recall
mode (p. 31) are on.
Applying Reverb to Each Group
Parameter
Value
Reverb send
-Inf dB – +10.0 dB
Returning the reverb send setting to its initial value
Group
Button
Individual group
That group’s [SOLO] button
All groups 1–8 [1-8] button
All groups 9–16 [9-16] button
Lit
Applying EQ to Each Group
Button
Parameter to adjust
[HI GAIN] button
High gain
[MID GAIN] button Mid gain
[MID FREQ] button Mid frequency
[LO GAIN] button Low gain
Parameter
Range EQ type
High gain
-15.0 dB – +15.0 dB
* Center frequency: 10 kHz
Shelving
Mid gain -15.0 dB – +15.0 dB
Peaking
Mid frequency 20 Hz – 20.0 kHz
Low gain
-15.0 dB – +15.0 dB
* Center frequency: 120 Hz
Shelving
Returning an EQ parameter to its initial value
Parameter
Button Initial value
High gain
[HI GAIN] button 0.0 dB
Mid gain [MID GAIN] button 0.0 dB
Mid frequency [MID FREQ] button 1.00 kHz
Low gain [LO GAIN] button 0.0 dB
Group
Button
Individual group
That group’s [SOLO] button
All groups 1–8 [1-8] button
All groups 9–16 [9-16] button
Lit
M-48_e.book 28 ページ ２００９年２月２４日 火曜日 午前９時３３分