Filter
Top Products
Panel Descriptions
9
[LO GAIN] button
This button allows you to adjust the EQ low gain.
The low gain (center frequency 120 Hz) can be boosted or cut by up
to 15 dB.
☞
“Applying EQ to Each Group” (p. 28)
[MID FREQ] button
This button allows you to adjust the EQ mid frequency
The center frequency of the mid frequency can be adjusted in a
range of 20 Hz–20.0 kHz.
☞
“Applying EQ to Each Group” (p. 28)
[MID GAIN] button
This button allows you to adjust the EQ mid gain.
The mid gain can be boosted or cut by up to 15 dB.
☞
“Applying EQ to Each Group” (p. 28)
[HI GAIN] button
This button allows you to adjust the EQ high gain.
The high gain (center frequency 10 kHz) can be boosted or cut by up
to 15 dB.
☞
“Applying EQ to Each Group” (p. 28)
Here you can perform memory operations.
[RECALL] button
This button turns memory Recall mode on/off.
When Recall mode is on, this button will light.
☞
“Storing Mixer Settings to Memory (Store)” (p. 30)
[STORE] button
This button turns memory Store mode on/off.
When Store mode is on, this button will light.
☞
“Recalling Mixer Settings from Memory (Recall)” (p. 31)
In this section you can adjust the input level of the AUX IN and the
ambient mic.
[AUX IN] knob
This adjusts the input level of the AUX IN L/R jack.
☞
“Adjusting the Input Level of AUX IN” (p. 27)
[AMBIENT MIC] mic
This adjusts the input level of the AMBIENT MIC.
☞
“Using the Built-in Ambient Mic” (p. 27)
In this section you can adjust the output level of the line out.
LINE OUT [VOLUME] knob
This knob adjusts the line out output level.
☞
“Adjusting the Line Out Output Level” (p. 29)
In this section you can make adjustments for the headphone output.
[REVERB] button
This button turns reverb on/off.
When reverb is on, this button will light.
☞
“Applying Reverb to Each Group” (p. 28)
[BASS] knob
This boosts/cuts the lower range (center frequency 120 Hz) by up to
15 dB.
☞
“Adjusting the Headphones Output Tone” (p. 29)
[TREBLE] knob
This boosts/cuts the upper range (center frequency 10 kHz) by up to
15 dB.
☞
“Adjusting the Headphones Output Tone” (p. 29)
[LIMITER] knob
This adjusts the limiter effect.
The limiter will be off if you turn the [LIMITER] knob to the OFF
position (all the way counter-clockwise).
By turning the [LIMITER] knob clockwise from the OFF position, you
can adjust the threshold level in a range of 0.0 dB – -40.0 dB.
The indicator above the [LIMITER] knob will light when the limiter
operates.
☞
“Applying a Limiter to the Headphones Output” (p. 29)
Level meter
This indicates the headphone output level.
About output muting
If only the -18 dB indicator is blinking, the M-48’s output has been
muted by an operation from the M-400 or the computer.
From the M-48, you can defeat muting by pressing any of the top
panel buttons.
PHONES [VOLUME] knob
This adjusts the headphone output level.
☞
“Adjusting the Headphones Output Level” (p. 29)
Control select section
(continued)
Memory section
Supplementary input section
Line out section
Headphone section
M-48_e.book 9 ページ ２００９年２月２４日 火曜日 午前９時３３分