Filter
Top Products
38
Settings Common to All Modes (System Mode)
EQ
MIDI/USB
Chord Memory
Parameter
Value Explanation
2 Band EQ
OFF, ON Switch the 2-Band equalizer
on/off.
LOW Freq 50, 63, 80, 100,
125, 160, 200,
250, 315, 400,
500, 630, 800,
1000, 1250, 1600,
2000, 2500, 3150,
4000 Hz
Selects the frequency of the low
range.
LOW Gain -15– +15 dB Adjusts the gain of the low fre-
quency. Positive (+) settings
will emphasize the low-fre-
quency range.
HIGH Freq 2000, 4000, 5000,
6300, 8000,
10000, 12500,
16000, 20000 Hz
Selects the frequency of the high
range.
HIGH Gain -15– +15 dB Adjusts the gain of the high fre-
quency. Positive (+) settings
will emphasize the high-fre-
quency range.
TOTAL
Gain
-15– +15 dB Adjusts the total gain.
Parameter
Value Explanation
Device ID
17–32 When you want to transmit or re-
ceive System Exclusive messages,
set this parameter to match the De-
vice ID number of the other MIDI
device.
Clock
Source
INT,
MIDI,
USB MIDI
The LFO cycle or multi-effects
changes can be synchronized to a
clock (tempo). When this is used
by the patch, this Clock Source set-
ting determines the clock which
will be used.
INT
: The Patch Tempo will be
used.
MIDI
: Synchronize to the clock of
an external MIDI.
USB MIDI
: Synchronize to the
clock of an external USB MIDI.
Rx Sw OFF, ON Specifies whether all MIDI mes-
sages will be received (ON) or not
(OFF).
Rx Channel 1–16 Sets the Basic Channel (MIDI chan-
nel on which the VC-2 receives and
transmits messages).
Rx PC OFF, ON Specifies whether Program
Change messages will be received
(ON) or not (OFF).
Rx Bank OFF, ON Specifies whether Bank Select mes-
sages will be received (ON) or not
(OFF).
Rx Sys-Ex OFF, ON Specifies whether System Exclu-
sive messages will be received
(ON) or not (OFF).
Tx Edit OFF, ON Specify whether changes you
make in the settings of a patch will
be transmitted as system exclusive
messages (ON), or will not be
transmitted (OFF).
Clock Out OFF, ON Specifies whether MIDI clock will
be transmitted (ON) or not (OFF).
USB-MIDI
Thru Sw
OFF, ON This switch specifies whether
MIDI messages received at the
MIDI connector will be re-trans-
mitted from the MIDI OUT con-
nector (ON) or not (OFF).
Volume
Expression
Level Con-
trol
OFF, ON Specifies whether received Vol-
ume or Expression Pedal messages
will adjust the output volume
(ON), or will be ignored (OFF).
Parameter
Value Explanation
Chord
Memory
Sw
OFF,
ON
Switches the Multi Chord Memory (one-
finger chord) function on/off.
* If you want to synchronize to an external
device, set Clock Source (p. 38) to
EXTERNAL, then get your external
device to transmit clock messages. If you
fail to do this, chords will not play
correctly.
Grid Reso-
lution
Dot-
ted 8th
note–
64th
note
Each note within the chord will be played
separately at the timing interval you
specify here.
Code set C–B Specify a chord for each key in the range
C–B.
KEEP OFF,
ON
When entering a chord from the key-
board, this parameter specifies whether
the keys you press will be held in their
pressed state (ON) or not (OFF). If this is
ON, the key will be maintained in a
“pressed” state even when you release it.
Parameter
Value Explanation
MIDI OUT
MIDI IN
V-Synth XT
USB OUT USB IN
USB-MIDI Thru Sw=OFF
MIDI OUT
MIDI IN
V-Synth XT
USB OUT USB IN
USB-MIDI Thru Sw=ON
Sound
Generator
Section
Sound
Generator
Section
vc2_for_XT_e1 38 ページ ２００５年３月８日 火曜日 午後４時５２分