Filter
Top Products
58
Effects List
35: Bass Multi
Bass Multi provides Comp/Limiter, Overdrive or Distortion,
3-band equalizer, and Chorus or Flanger effects connected in
series. This algorithm is a multi-effects for bass.
36: E.Piano Multi
Enhancer, Phaser, Chorus or Flanger, and Tremolo or Auto-
pan are connected in series. This effect is used for electric
piano.
Parameter
Value Description
Comp Sw
OFF, ON Turns the comp/limiter on/off.
Comp
Threshold
-60–0 dB Sets the volume level at which the
compression begins.
Comp Attack 0–127 Sets the time after the sound vol-
ume is crossed the compressor
threshold until compression be-
gins.
Comp Re-
lease
0–127 Specifies the time from when the
volume drops below the compres-
sor threshold until compression is
no longer applied.
Comp Ratio 1.5:1, 2:1, 4:1,
100:1
Sets the “source sound:output
sound” compression ratio.
Comp Gain -60– +12 dB Adjusts the output gain.
Od/Ds Sw OFF, ON Selects whether to use overdrive
or distortion.
Drive Mode OD, DS Selects whether to use overdrive
(OD) or distortion (DS).
Drive 0–127 Degree of distortion
Amp Sim Sw OFF, ON Turns the amp simulator on/off.
Amp Type SMALL,
BUILT-IN,
2-STACK
(STACK)
Type of guitar amp
SMALL: small amp
BUILT-IN: single-unit type amp
2-STACK: large double stack amp
Distortion
(DS) Level
0–127 Volume of the overdrive or distor-
tion sound.
EQ Low Freq 50–4000 Hz Frequency of the low range
EQ Low Gain -15– +15 dB Gain of the low range
EQ Mid Freq 50–20000 Hz Frequency of the middle range
EQ Mid Q 0.5, 0.7, 1.0, 2.0,
4.0, 8.0
Gain of the middle range
Set a higher value for Q to narrow
the range to be affected.
EQ Mid Gain -15– +15 dB Gain of the middle range
EQ Hi Freq 2000–20000 Hz Frequency of the high range
EQ Hi Gain -15– +15 dB Gain of the high range
Mod Mode CHORUS,
FLANGER
Selects whether to use chorus or
flanger.
Mod Rate 0.05–10.0 Hz,
note
Adjusts the speed of modulation
for the chorus or flanger.
Mod Depth 0–127 Adjusts the depth of modulation
for the chorus or flanger.
Mod Phase 0–180 deg Sets how the chorus or flanger
sound is spread.
Mod Pre De-
lay
0–50.0 ms Adjusts the delay time from the di-
rect sound until the chorus or
flanger sound is heard.
Mod Feed-
back
-98– +98 % Adjusts the proportion of the ef-
fect sound that is fed back into the
effect. Negative (-) settings will in-
vert the phase.
Mod Xover-
LPF
500–15000 Hz,
THRU
Adjusts the cutoff frequency of the
low pass filter. (THRU: no filter is
used)
Mod Xover-
HPF
THRU,
50–800 Hz
Adjusts the cutoff frequency of the
high pass filter. (THRU: no filter is
used)
Mod Level 0–127 Volume of the chorus or flanger
sound.
Parameter
Value Description
Enhan Sw
OFF, ON Turns the enhancer effect on/off.
Enhan Sens 0–127 Sensitivity of the enhancer
Enhan Fre-
quency
0–127 Sets the lower limit of the frequencies
to which the enhancement effect is
added.
Enhan Mix
Level
0–127 Level of the overtones generated by
the enhancer
Enhan Lev-
el
0–127 Volume of the enhancer sound
Phaser
Manual
0–127 Specifies the center frequency at
which the sound is modulated.
Phaser Rate 0.05–10.0
Hz, note
Specifies the frequency of modula-
tion.
Phaser
Depth
0–127 Specifies the depth of modulation.
Phaser Res-
onance
0–127 Specifies the amount of feedback for
the phaser.
Higher settings will give the sound a
stronger character.
Phaser Mix
Level
0–127 Specifies the volume of the phase-
shifted sound, relative to the direct
sound.
Mod Mode CHORUS,
FLANGER
Selects whether to use chorus or
flanger.
Mod Rate 0.05–10.0
Hz, note
Adjusts the speed of modulation for
the chorus or flanger.
Mod Depth 0–127 Adjusts the depth of modulation for
the chorus or flanger.
Mod Phase 0–180 deg Sets how the chorus or flanger sound
is spread.
Mod Pre
Delay
0–50.0 ms Adjusts the delay time from the direct
sound until the chorus or flanger
sound is heard.
Mod Feed-
back
-98– +98 % Adjusts the proportion of the effect
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Mod Xover-
LPF
500–15000
Hz, THRU
Adjusts the cutoff frequency of the
low pass filter. (THRU: no filter is
used)
Mod Xover-
HPF
THRU, 50–
800 Hz
Adjusts the cutoff frequency of the
high pass filter. (THRU: no filter is
used)
Parameter
Value Description
vc2_for_XT_e1 58 ページ ２００５年３月８日 火曜日 午後４時５２分