Filter
Top Products
52
Effects List
22: Step Flanger
This is a flanger in which the flanger pitch changes in steps.
The speed at which the pitch changes can also be specified in
terms of a note-value of a specified tempo.
23: Analog Phaser
This effect features two analog-type phasers arranged in
parallel, making it stereo compatible. The sound as it
cyclically drifts in and out of phase is added to the source
sound, creating the modulation with the characteristic of
phasers.
Phase
0–180 deg Specifies the spaciousness of the
flanger sound.
Feedback
Mode
NORMAL,
CROSS
Specifies the input destination to
which the flanger sound will be re-
turned.
NORMAL: The left flanger sound
will be returned to the left input,
and the right flanger sound to the
right input.
CROSS: The left flanger sound will
be returned to the right input, and
the right flanger sound to the left
input.
Feedback -98– +98 % This setting makes the flanging
sound of each of right and left
channels return to the input of the
opposite channel. Negative (-) set-
tings will invert the phase.
* When the Feedback Mode is set to
NORMAL, this setting will be ig-
nored.
Cross Mix
Level
-100– +100 This setting makes the flanging
sound from each of the right and
left channels mix it with the flang-
ing sound of the opposite channel.
Negative (-) settings will invert the
phase.
Ps Low Freq 50–4000 Hz Frequency of the low range
Ps Low Gain -15– +15 dB Gain of the low range
Ps Hi Freq 2000–20000 Hz Frequency of the high range
Ps Hi Gain -15– +15 dB Gain of the high range
Parameter
Value Description
Pre Dly Time
0–50.0 ms Specifies the time delay from the
original sound until the flanger
sound is heard.
Rate 0.05–10.0 Hz,
note
Specifies the modulation frequen-
cy of the flanger sound.
Depth 0–127 Specifies the modulation depth of
the flanger sound.
Feedback -98– +98 % Adjusts the proportion of the
flanger sound that is fed back into
the effect. Negative (-) settings will
invert the phase.
Phase 0–180 deg Specifies the spaciousness of the
flanger sound.
Step Rate 0.05–10.0 Hz,
note
Specifies the frequency of pitch
change.
Flanger Level 0–127 Volume of the flanger sound
Ps Low Freq 50–4000 Hz Frequency of the low range
Ps Low Gain -15– +15 dB Gain of the low range
Ps Hi Freq 2000–20000 Hz Frequency of the high range
Ps Hi Gain -15– +15 dB Gain of the high range
Parameter
Value Description
Parameter Value Description
Shift Mode 4STAGE,
8STAGE
Sets the number of stages in the
phase shift circuit (four (4STAGE) or
eight (8STAGE)).
Setting this to eight stages (8STAGE)
increases the number of the frequen-
cy points that sound is canceled,
giving a sharper effect.
Center Freq 0–127 Sets the center frequency to which
the phaser effect is applied.
Increasing this value moves the ef-
fect point of the phaser into higher
frequency ranges.
Resonance 0–127 Amount of feedback
Increasing this value gives a more
distinctive sound to the effect.
LFO 1/2
Rate
0.02–5.00 Hz,
note
Sets the rate of the swelling sound.
LFO 1/2
Depth
0–127 Specifies the depth of modulation.
LFO 1/2
Phase
NORM, INV Sets the phase of both left and right
swelling.
NORM: The left and right phase will
be the same.
INV: The left and right phase will be
opposite.
Freq.
Level
Freq.
Level
4 stage
8 stage
vc2_for_XT_e1 52 ページ ２００５年３月８日 火曜日 午後４時５２分