Filter
Top Products
E-62
Appendix
08: Rotary
This is a rotary speaker simulator.
Parameter Value Ranges:
0 :Speed (Slow, Fast)
Switches the speed mode between fast and slow.
1 :Brake (Rotate, Stop)
Stops speaker rotation.
2 :Fall Acceleration (0 to 127)
Adjusts acceleration when the speed mode is switched from fast
to slow.
3 :Rise Acceleration (0 to 127)
Adjusts acceleration when the speed mode is switched from slow
to fast.
4 :Slow Rate (0 to 127)
Adjusts the speaker rotation speed in the slow speed mode.
5 :Fast Rate (0 to 127)
Adjusts the speaker rotation speed in the fast speed mode.
09: Drive Rotary
This is an overdrive - rotary speaker simulator.
Parameter Value Ranges:
0 :Overdrive Gain (0 to 127)
Adjusts overdrive gain.
1 :Overdrive Level (0 to 127)
Adjusts the overdrive output level.
2 :Speed (Slow, Fast)
Switches the speed mode between fast and slow.
3 :Brake (Rotate, Stop)
Stops speaker rotation.
4 :Fall Acceleration (0 to 127)
Adjusts acceleration when the speed mode is switched from fast
to slow.
5 :Rise Acceleration (0 to 127)
Adjusts acceleration when the speed mode is switched from slow
to fast.
6 :Slow Rate (0 to 127)
Adjusts the speaker rotation speed in the slow speed mode.
7 :Fast Rate (0 to 127)
Adjusts the speaker rotation speed in the fast speed mode.
10: 3-Phase Chorus
This is a 3-phase chorus effect using two LFOs with different sine
wave rates.
Parameter Value Ranges:
0 :Rate 1 (Fast LFO State) (0 to 127)
Adjusts the rate of LFO 1.
1 :Depth 1 (Fast LFO Depth) (0 to 127)
Adjusts the depth of LFO 1.
2 :Rate 2 (Slow LFO State) (0 to 127)
Adjusts the rate of LFO 2.
3 :Depth 2 (Slow LFO Depth) (0 to 127)
Adjusts the depth of LFO 2.
4 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
11: Auto Pan
Performs continual left-right panning of the input signal using an
LFO.
Parameter Value Ranges:
0 :Rate (0 to 127)
Adjusts the panning rate.
1 :Depth (0 to 127)
Adjusts the panning depth.
12: Stereo Phaser
This is a stereo phaser that modulates the phase using a sine wave
LFO.
Parameter Value Ranges:
0 :Resonance (0 to 127)
Adjusts the strength of the resonance.
1 :Manual (–64 to 0 to +63)
Adjusts the reference phaser shift amount.
2 :Rate (0 to 127)
Adjusts the LFO rate.
3 :Depth (0 to 127)
Adjusts the LFO depth.
4 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
13: Phaser
This is a monaural phaser that modulates the phase using a sine
wave LFO.
Parameter Value Ranges:
0 :Resonance (0 to 127)
Adjusts the strength of the resonance.
1 :Manual (–64 to 0 to +63)
Adjusts the reference phaser shift amount.
2 :Rate (0 to 127)
Adjusts the LFO rate.
3 :Depth (0 to 127)
Adjusts the LFO depth.
4 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
14: Distortion
This effect provides Distortion + Amp Simulator.
Parameter Value Ranges:
0 :Gain (0 to 127)
Adjusts the input signal gain.
1 :Low (0 to 127)
Adjusts the low-range gain.
The cutoff frequency depends on the DSP type.
2 :High (0 to 127)
Adjusts the high gain.
The cutoff frequency depends on the DSP type.
3 :Level (0 to 127)
Adjusts the output level.