Filter
Top Products
Editing sounds | TREBLE EDIT parameters
42
r
FR-7/FR-5 V-Accordion
2.3 Reed Volume
(Off, –30~“Std”~30, Default set-
ting: Std) Here comes the last
parameter that can be set for
each reed/footage individually.
It allows you to create the
desired “mix” (volume balance) for the active reeds (see
the “2.2 Register” page).
This is a relative parameter, which means that its value
is added to or subtracted from the standard value
(“Std”). As a rule, it would be wise to decide which reed
is most important and set its Volume parameter to
“Std”. Then reduce or increase the volume of the “ancil-
lary” reeds to create the desired balance.
Note: The overall volume of the Treble section (all registers) can
be changed using the [BALANCE] knob.
2.4 Treble Octave
(–1, 0, 1, Default setting: 0) This
parameter allows you to trans-
pose the selected register one
octave up (“1”) or down (“–1”).
This can be used for two pur-
poses: to quickly correct the pitch that results from the
active reeds (see above) or to avoid overlaps of the
selected register when using a Treble Orchestra sound.
(The Orchestra section also provides an Octave parame-
ter.)
2.5 Valve Noise
Here comes a more elaborate
version of the Noise parameter
discussed on page 30, because it
allows you not only to set the
level of the “typical” valve
noises, but also to specify what kind of instrument
should generate the noise. Though you are free to
experiment with any noise type you like, using the noise
related to the selected instrument (see “2.1 Reed Type”)
is usually more realistic.
There is only one TYPE for the entire register (i.e. all 7
reeds). The options are: Bandoneon, I-Folk, I-Folk2, Clas-
sic, Cajun, Jazz, F-Folk, D-Folk, Organetto, F-Folk2,
Classic2, Studio, Tradition, Steierische, OldItaly, TexMex,
Trikitixa.
Use the LEVEL parameter to specify how prominent the
noise should be (–30~“Std”~30, Default setting: Std).
Note: Whenever you select “ALL” for “2.1 Reed Type” and set a
different reed type, this noise setting is automatically adapted to
the reed type. It would therefore be a good idea to first select the
reed type and only then change the noise type.
2.6 Musette Detune
This parameter allows you to
choose the system used for
detuning the 8’ reeds. See
page 28 for details. The options
are: Off, Dry, Classic, F-Folk,
American_L, American_H, North_Eur, German_L,
D-Folk_L, Italian_L, German_H, Alpine, Italian_H,
D-Folk_H, French, Scottish.
2.7 Bellows Detune
(Off, Low, Standard, High,
Default setting: Standard) This
parameter further adds to the
realism of the sounds emulated
by your FR-7/FR-5. Here, you
can specify how strongly the pitch of the simulated
Treble reed(s) changes when you open or close the bel-
lows faster than usual.
If the “Standard” setting seems too mild, try “High”. If it
is too strong, use “Low”. If you don’t want any detuning
effect, select “Off”. The most convincing setting usually
depends on the selected instrument(s) (see “2.1 Reed
Type”).
2.8 Reverb Send, 2.9 Chorus Send,
2.10 Delay Send
(0~127 for all three) Use these
parameters to set the Reverb, Chorus
or Delay send level (how much effect
should be applied to the Treble sec-
tion). The higher the value you set,
the more the Treble section is pro-
cessed by the effect in question.
It works much the same way as a
cathedral: the louder you sing, the
more reverb (chorus or delay) you
hear. In the case of the cathedral, singing louder means
that you increase the effect send level, i.e. the level of
the signal (your voice) that will be processed by the
acoustic environment.
The other sections (Bass, Free Bass, etc.) have the same
parameters, so that you can create a sound image with
various “levels” (foreground, background).
The effects themselves can be edited on separate pages
(see p. 56).
2.11 Aftertouch Pitch
(Off, 1/4 Down, 1/2 Down, 1/4
Up, 1/2 Up, Default setting: Off)
As stated earlier, the FR-7/
FR-5’s Treble keyboard also gen-
erates aftertouch messages.
“Aftertouch” refers to the fact that you press a key even
further down after playing a note. This effect allows
you to bend the pitch down (temporarily lower the
note) by a quarter (“1/4 Down”) or a semi-tone (“1/2
Down”). Select “1/4 Up” or “1/2 Up” to bend the notes
up a quarter or a semi-tone. Select “Off” to switch off
the Treble section’s aftertouch recognition.
Note: This aftertouch effect applies to all notes that are sound-
ing simultaneously. If you play a chord and then only press down
one key of the chord’s constituent notes, all notes are bent by the
same amount. (MIDI buffs call this “channel aftertouch”.)
2.12 Bass Link
Here are two parameters that
allow you specify which Bass
and/or Orchestra Bass register/
sound are selected whenever
you press the Treble register you