Filter
Top Products
Archiving your settings via MIDI (Bulk Dump)
V-Accordion
r
75
Archiving your settings via MIDI (Bulk Dump)
MIDI can also be used for transmitting parameter and memory settings from the FR-7/FR-5 to an external MIDI device
and back.
Archiving your settings with a sequencer
The Bulk Dump parameters allow you to transmit the
contents of one or all Set memories to a second FR-7 or
FR-5, an external sequencer, computer or data filer.
Sending these data to other instruments (a digital
piano, synthesizer, etc.) does nothing at all. That’s
because the setting data are special MIDI messages only
one model (or model family) understands. They are
called “system exclusive messages” – or “SysEx” for
short. By transmitting them to a second FR-7/FR-5,
however, you can “copy” the settings of your V-Accor-
dion to that of a friend, colleague or student.
Even a sequencer or data filer does not know what the
messages mean and so does not use them in any way. It
merely records them. Afterwards, you only need to start
playback on your sequencer or data filer to transmit the
settings back to the FR-7/FR-5.
(1) Connect the FBC-7’s MIDI OUT socket to the
sequencer’s/computer’s MIDI IN socket.
See page 66 for a connection diagram. Obviously, you
also need to connect the FR-7/FR-5 to the FBC-7.
Note: Your computer needs to be equipped with (or connected
to) an appropriate MIDI interface.
(2) If you are working with a computer, launch the
sequencer program.
(3) Create or select an empty song.
(4) Create (or select) an empty track.
The track’s MIDI channel is of no importance here.
You need to ensure, however, that the sequencer/
program accepts SysEx data. If necessary, switch off
the MIDI filter in question (see the manual of your
sequencer or software).
(5) Switch off the sequencer’s MIDI Echo (or Soft Thru)
function.
If that’s too tedious, disconnect the MIDI cable from
the sequencer’s/computer’s MIDI OUT socket. This is
to ensure that the sequencer doesn’t transmit the
SysEx data back to the FR-7/FR-5 right away, which
might cause problems.
(6) Activate the record-ready mode of the track you
selected/created.
Note: It would be wise not to change the tempo on your
sequencer/in the software. By default, most sequencers/pro-
grams use the tempo value = 120. Leave it that way (or else
do whatever is necessary to ensure that the new tempo value
is stored along with the data).
(7) If you want to archive the settings of just one Set
(9.8 Bulk Dump SET), select it on the FR-7/FR-5
using the SET [√][®] buttons.
(8) On the FR-7/FR-5, press and hold the [EXIT÷JUMP]
button, then press register [9].
Depending on whether you want to archive all Sets
or just the settings of one Set, either press register [7]
(9.7 Bulk Dump ALL) or [8] (9.8 Bulk Dump SET). The
display now responds with:
Before going on tour, etc., select “ALL” to make a
backup copy of your Sets. Select “SET” to transmit
only the settings that are actually needed for the
song in question. This transmits the settings of the
Set you are currently using.
(9) Start recording on your sequencer/computer.
Wait until the count-in (one or two measures) is fin-
ished, then…
(10) Press [MENU÷WRITE] on the FR-7/FR-5 to start the
transmission of the bulk data.
The display now responds with:
Press [EXIT÷JUMP] if you do not want to transmit your
settings after all.
(11) Wait until the following message appears, then
stop recording on your sequencer.
(12) Name the “song” (it may only contain data so far)
and save it to hard or floppy disk.
To transmit the settings back to the FR-7/FR-5 at a
later stage, see below.
–OR–
–OR–