Filter
Top Products
76
Adding effects
20: 3 TAP DELAY (Triple Tap Delay)
The Triple Tap Delay produces three delay sounds; center, left and
right.
fig.MFX-20
21: 4 TAP DELAY (Quadruple Tap
Delay)
The Quadruple Tap Delay has four delays.
fig.MFX-21a
The stereo location of each delay sound is as follows.
fig.MFX-21b
Low Gain
-15– +15 [dB] Adjusts the gain of the low fre-
quency.
High Gain -15– +15 [dB] Adjusts the gain of the high fre-
quency.
Balance # D100:0W–
D0:100W
Adjusts the volume balance be-
tween the direct sound and the
modulation delay sound.
With a setting of D100:0W only
the direct sound will be output,
and with a setting of D0:100W
only the modulation delay
sound will be output.
Level 0–127 Adjusts the output level.
Parameter
Value Description
Delay Left
0–840 [ms],
note *1
Adjusts the time delay from the
direct sound until when the left
delay sound is heard.
Delay Right 0–840 [ms],
note *1
Adjusts the time delay from the
direct sound until when the
right delay sound is heard.
Delay Center 0–840 [ms],
note *1
Adjusts the time delay from the
direct sound until when the cen-
ter delay sound is heard.
Feedback # -98– +98 [%] Adjusts the proportion (%) of
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
HF Damp 200–8000 [Hz],
BYPASS
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Left Level 0–127 Adjusts the volume of the left
delay sound.
Right Level 0–127 Adjusts the volume of the right
delay sound.
Center Level 0–127 Adjusts the volume of the center
delay sound.
Low Gain -15– +15 [dB] Adjusts the gain of the low fre-
quency.
High Gain -15– +15 [dB] Adjusts the gain of the high fre-
quency.
Parameter
Value Description
L in
R in
L out
R out
Left Tap
Right Tap
Triple Tap Delay
2-Band
EQ
2-Band
EQ
Balance W
Balance D
Balance W
Balance D
Feedback
Center Tap
Balance #
D100:0W–
D0:100W
Adjusts the volume balance be-
tween the direct sound and the
delay sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
delay sound will be output.
Level 0–127 Adjusts the output level.
Parameter
Value Description
Delay 1
0–840 [ms],
note *1
Adjusts the time delay from the
direct sound until when delay 1
sound is heard.
Delay 2 0–840 [ms],
note *1
Adjusts the time delay from the
direct sound until when delay 2
sound is heard.
Delay 3 0–840 [ms],
note *1
Adjusts the time delay from the
direct sound until when delay 3
sound is heard.
Delay 4 0–840 [ms],
note *1
Adjusts the time delay from the
direct sound until when delay 4
sound is heard.
Level 1 0–127 Adjusts the volume of delay 1
sound.
Level 2 0–127 Adjusts the volume of delay 2
sound.
Level 3 0–127 Adjusts the volume of delay 3
sound.
Level 4 0–127 Adjusts the volume of delay 4
sound.
Feedback # -98– +98 [%] Adjusts the proportion (%) of
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
Parameter
Value Description
L in
R in
L out
R out
Quadruple Tap Delay
Balance W
Balance D
Balance W
Balance D
Delay 1
Delay 2
Delay 3
Delay 4
Feedback
1
23
4
L
R
JUNO-D_e.book 76 ページ ２００４年６月１１日 金曜日 午後１時２１分