Filter
Top Products
83
Adding effects
Effects
38: CHO>FLANGER (Chorus
→
Flanger)
This effect connects a chorus and a flanger in series.
fig.MFX-38
39: CHORUS/DELAY
This effect connects a chorus and a delay in parallel. The parameters
are the same as for “36: CHORUS
>
DELAY.” However, the Dly
Balance parameter adjusts the volume balance between the direct
sound and the delay sound.
fig.MFX-39
40: FLG/DELAY (Flanger/Delay)
This effect connects a flanger and a delay in parallel. The parameters
are the same as for “37: FLG>DELAY.” However, the Dly Balance
parameter adjusts the volume balance between the direct sound and
the delay sound.
41: CHO/FLANGER (Chorus/
Flanger)
This effect connects a chorus and a flanger in parallel. The
parameters are the same as for “38: CHO>FLANGER.” However, the
Flanger Balance parameter adjusts the volume balance between the
direct sound and the flanger sound.
fig.MFX-41
42: LOFI
This effect intentionally degrades the audio quality to simulate a Lo-
Fi sound. It is particularly effective on drums.
fig.MFX-42
Parameter
Value Description
Cho Delay
0.0–100 [ms] Adjusts the time delay from
when the direct sound begins
until the chorus sound is heard.
Cho Rate 0.05–10.00 [Hz] Adjusts the modulation speed of
the chorus effect.
Cho Depth 0–127 Adjusts the modulation depth of
the chorus effect.
Cho Balance # D100:0W–
D0:100W
Adjusts the volume balance be-
tween the direct sound and the
chorus sound.
With a setting of “D100:0W,” only
the direct sound will be output.
With a setting of “D0:100W,” only
the chorus sound will be output.
Flg Delay 0.0–100 [ms] Adjusts the time delay from
when the direct sound begins
until the flanger sound is heard.
Flg Rate 0.05–10.00 [Hz] Adjusts the modulation speed of
the flanger effect.
Flg Depth 0–127 Adjusts the modulation depth of
the flanger effect.
Flg Feedback -98– +98 [%] Adjusts the proportion (%) of
the flanger sound that is fed
back into the effect.
Negative (-) settings will invert
the phase.
Flg Balance # D100:0W–
D0:100W
Adjusts the volume balance be-
tween the chorus sound and the
chorus sound that is passed
through the flanger.
With a setting of “D100:0W,” only
the chorus sound will be output.
With a setting of “D0:100W,” only
the chorus sound that passes
through the flanger will be output.
Level 0–127 Adjusts the output level.
Feedback
Flanger
L in
R in
L out
R out
Balance W
Balance W
Balance D
Balance D
Chorus
Balance W
Balance W
Balance D
Balance D
R in R out
L in L out
Feedback
Balance W
Balance D
Balance W
Balance D
Chorus
Delay
Parameter
Value Description
Bit Down
0–11 This setting lowers the audio
quality.
The audio quality will worsen as
this setting is increased.
S-RateDown 0–7 This coarsens the output signal.
The sound will become coarser
as this setting is increased.
Post Gain 0, +6, +12, +18
[dB]
Adjusts the output signal.
Low Gain -15– +15 [dB] Adjusts the gain of the low fre-
quency.
High Gain -15– +15 [dB] Adjusts the gain of the high fre-
quency.
Output MONO, STE-
REO
Specifies how the sound will be
output.
With a setting of “MONO,” the
output sound will be monaural.
Level # 0–127 Specifies the output volume
from the Lo-Fi effect.
R in R out
L in L out
Feedback
Balance W
Balance D
Balance W
Balance D
Chorus
Flanger
L in
R in
L out
R out
Lo-Fi
2-Band EQ
2-Band EQ
Lo-Fi
JUNO-D_e.book 83 ページ ２００４年６月１１日 金曜日 午後１時２１分