Filter
Top Products
80
Adding effects
29: OD>DELAY (Overdrive
→
Delay)
This effect connects an overdrive and a delay in series.
fig.MFX-29
30: DIST>CHORUS
(Distortion
→
Chorus)
This effect connects distortion and chorus in series. The parameters
are essentially the same as “27: OD>CHORUS,” with the exception
of the following two.
OD Drive
→
Dist Drive (Specifies the amount of distortion.)
OD Pan
→
Dist Pan (Specifies the stereo location of the distortion
sound.)
fig.MFX-30
31: DIST>FLANGER
(Distortion
→
Flanger)
This effect connects distortion and flanger in series. The parameters
are essentially the same as in “28: OD>FLANGER,” with the
exception of the following two.
OD Drive
→
Dist Drive (Specifies the amount of distortion.)
OD Pan
→
Dist Pan (Specifies the stereo location of the distortion
sound.)
fig.MFX-31
32: DIST>DELAY (Distortion
→
Delay)
This effect connects distortion and delay in series. The parameters
are essentially the same as in “29: OD
>
DELAY,” with the exception
of the following two.
OD Drive
→
Dist Drive (Specifies the amount of distortion.)
OD Pan
→
Dist Pan (Specifies the stereo location of the distortion
sound.)
fig.MFX-32
Flg Balance #
D100:0W–
D0:100W
Adjusts the volume balance be-
tween the overdrive sound that
is sent through the flanger and
the overdrive sound that is not
sent through the flanger.
With a setting of “D100:0W,”
only the overdrive sound will be
output. With a setting of
“D0:100W,” only the overdrive
sound that is sent through the
flanger will be output.
Level 0–127 Adjusts the output level.
Parameter
Value Description
OD Drive
0–127 Adjusts the degree of overdrive
distortion.
The volume will change togeth-
er with the degree of distortion.
OD Pan # L64–63R Adjusts the stereo location of the
overdrive sound.
L64 is far left, 0 is center, and
63R is far right.
Delay Time 0–500 [ms] Adjusts the time delay from
when the direct sound begins
until the delay sound is heard.
Dly Feedback -98– +98 [%] Adjusts the proportion (%) of
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
Dly HF Damp 200–8000 [Hz],
BYPASS
Adjusts the frequency above
which delayed sound fed back
to the effect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Dly Balance # D100:0W–
D0:100W
Adjusts the volume balance be-
tween the overdrive sound that
is sent through the delay and the
overdrive sound that is not sent
through the delay.
With a setting of “D100:0W,”
only the overdrive sound will be
output. With a setting of
“D0:100W,” only the overdrive
sound that is sent through the
delay will be output.
Level 0–127 Adjusts the output level.
Parameter
Value Description
L in
R in
Delay
Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
L in
R in
Chorus
Distortion
L out
R out
Balance W
Balance W
Balance D
Balance D
L in
R in
Flanger
Distortion
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
L in
R in
Delay
Distortion
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
JUNO-D_e.book 80 ページ ２００４年６月１１日 金曜日 午後１時２１分