Filter
Top Products
81
Adding effects
Effects
33: ENH>CHORUS (Enhancer
→
Chorus)
This effect connects an enhancer and a chorus in series.
fig.MFX-33
34: ENH>FLANGER (Enhancer
→
Flanger)
This effect connects an enhancer and a flanger in series.
fig.MFX-34
35: ENH>DELAY (Enhancer
→
Delay)
This effect connects an enhancer and a delay in series.
fig.MFX-35
Parameter
Value Description
Enhancer Sens #
0–127 Adjusts the sensitivity of the en-
hancer.
Enhancer Mix 0–127 Adjusts the ratio with which the
overtones generated by the en-
hancer are combined with the
direct sound.
Cho Delay 0.0–100 [ms] Adjusts the time delay from
when the direct sound begins
until the chorus sound is heard.
Cho Rate 0.05–10.00 [Hz] Adjusts the modulation speed of
the chorus effect.
Cho Depth 0–127 Adjusts the modulation depth of
the chorus effect.
Cho Balance # D100:0W–
D0:100W
Adjusts the volume balance be-
tween the enhancer sound that
is sent through the chorus and
the enhancer sound that is not
sent through the chorus.
With a setting of “D100:0W,”
only the enhancer sound will be
output. With a setting of
“D0:100W,” only the enhancer
sound that is sent through the
chorus will be output.
Level 0–127 Adjusts the output level.
Parameter
Value Description
Enhancer Sens #
0–127 Adjusts the sensitivity of the en-
hancer.
Enhancer Mix 0–127 Adjusts the ratio with which the
overtones generated by the en-
hancer are combined with the
direct sound.
Flg Delay 0.0–100 [ms] Adjusts the time delay from
when the direct sound begins
until the flanger sound is heard.
Flg Rate 0.05–10.00 [Hz] Adjusts the modulation speed of
the flanger effect.
Flg Depth 0–127 Adjusts the modulation depth of
the flanger effect.
Chorus
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
Balance W
Balance W
Balance D
Balance D
Feedback
Flanger
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
Balance W
Balance W
Balance D
Balance D
Flg Feedback
-98– +98 [%] Adjusts the proportion (%) of
the flanger sound that is fed
back into the effect.
Negative (-) settings will invert
the phase.
Flg Balance # D100:0W–
D0:100W
Adjusts the volume balance be-
tween the enhancer sound that
is sent through the flanger and
the enhancer sound that is not
sent through the flanger.
With a setting of “D100:0W,”
only the enhancer sound will be
output. With a setting of
“D0:100W,” only the enhancer
sound that is sent through the
flanger will be output.
Level 0–127 Adjusts the output level.
Parameter Value Description
Enhancer Sens #
0–127 Adjusts the sensitivity of the en-
hancer.
Enhancer Mix 0–127 Adjusts the ratio with which the
overtones generated by the en-
hancer are combined with the
direct sound.
Delay Time 0–500 [ms] Adjusts the time delay from
when the direct sound begins
until the delay sound is heard.
Dly Feedback 98– +98 [%] Adjusts the proportion (%) of
the delay sound that is fed back
into the delay input.
Negative (-) settings will invert
the phase.
Dly HF Damp 200–8000 [Hz],
BYPASS
Adjusts the frequency above
which delayed sound fed back
to the delay input will be cut.
If you do not want to cut the
high frequencies of the delay
feedback, set this parameter to
BYPASS.
Dly Balance # D100:0W–
D0:100W
Adjusts the volume balance be-
tween the enhancer sound that
is sent through the delay and the
enhancer sound that is not sent
through the delay.
With a setting of “D100:0W,”
only the enhancer sound will be
output. With a setting of
“D0:100W,” only the enhancer
sound that is sent through the
delay will be output.
Level 0–12 Adjusts the output level.
Parameter
Value Description
Feedback
Delay
L in
R in
L out
R out
Mix
Mix
Enhancer
Enhancer
Balance W
Balance W
Balance D
Balance D
JUNO-D_e.book 81 ページ ２００４年６月１１日 金曜日 午後１時２１分