Filter
Top Products
77
Adding effects
Effects
22: TM CTRL DLY (Time Control Delay)
You can change the delay time in real time. Lengthening the delay
will lower the pitch, and shortening it will raise the pitch.
fig.MFX-22
23: 2V PCH SHIFT (2-Voice Pitch
Shifter)
A Pitch Shifter shifts the pitch of the direct sound. This 2-voice pitch
shifter has two pitch shifters, and can add two pitch shifted sounds
to the direct sound.
fig.MFX-23
HF Damp
200–8000 [Hz],
BYPASS
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Balance # D100:0W–
D0:100W
Adjusts the volume balance be-
tween the direct sound and the
delay sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
delay sound will be output.
Level 0–127 Adjusts the output level.
Parameter
Value Description
Delay #
0–840 [ms] Adjusts the time delay from the
direct sound until when each de-
lay sound is heard.
Feedback # -98– +98 [%] Adjusts the proportion (%) of
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
Acceleration 0–15 This parameter adjusts the time
over which the Delay Time will
change from the current setting
to a newly specified setting.
The rate of change for the Delay
Time directly affects the rate of
pitch change.
HF Damp 200–8000 [Hz],
BYPASS
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Pan L64–63R Adjusts the stereo location of the
delay sound.
L64 is far left, 0 is center, and
63R is far right.
Low Gain -15– +15 [dB] Adjusts the gain of the low fre-
quency.
High Gain -15– +15 [dB] Adjusts the gain of the high fre-
quency.
Parameter
Value Description
L in
R in
L out
R out
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
2-Band
EQ
Feedback
Time Control Delay
Balance
D100:0W–
D0:100W
Adjusts the volume balance be-
tween the direct sound and the
delay sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
delay sound will be output.
Level 0–127 Adjusts the output level.
Parameter
Value Description
Mode
1, 2, 3, 4, 5 Higher settings of this parame-
ter will result in slower re-
sponse, but steadier pitch.
Coarse A #1 -24– +12 [semi] Adjusts the pitch of Pitch Shift A
in semitone steps (-2- +1 oc-
taves).
Coarse B #2 -24– +12 [semi] Adjusts the pitch of Pitch Shift B
in semitone steps (-2- +1 oc-
taves).
Fine A #1 -100– +100
[cent]
Makes fine adjustments to the
pitch of Pitch Shift A in 2-cent
steps (-100- +100 cents).
One cent is 1/100th of a semi-
tone.
Fine B #2 -100– +100
[cent]
Makes fine adjustments to the
pitch of Pitch Shift B in 2-cent
steps (-100- +100 cents).
One cent is 1/100th of a semi-
tone.
Pre Delay A 0–500 [ms] Adjusts the time delay from
when the direct sound begins
until the Pitch Shift A sound is
heard.
Pre Delay B 0–500 [ms] Adjusts the time delay from
when the direct sound begins
until the Pitch Shift A sound is
heard.
Pan A L64–63R Adjusts the stereo location of the
Pitch Shift A sound.
L64 is far left, 0 is center, and
63R is far right.
Pan B L64–63R Adjusts the stereo location of the
Pitch Shift B sound.
L64 is far left, 0 is center, and
63R is far right.
Parameter
Value Description
L in
R in
L out
R out
2Voice Pitch Shifter
Level Balance A
Balance W
Balance D
Balance W
Balance D
Level Balance B
PanB R
PanA L
PanA R
PanB L
JUNO-D_e.book 77 ページ ２００４年６月１１日 金曜日 午後１時２１分