Filter
Top Products
65
This is a stereo flanger. (The LFO has the same phase for left and
right.) It produces a metallic resonance that rises and falls like a jet
airplane taking off or landing. A filter is provided so that you can
adjust the timbre of the flanged sound.
fig.MFX-24
This is a flanger in which the flanger pitch changes in steps. The speed
at which the pitch changes can also be specified in terms of a note-
value of a specified tempo.
fig.MFX-25
Uses a six-phase chorus (six layers of chorused sound) to give richness
and spatial spread to the sound.
fig.MFX-26
24: FLANGER
Parameter Value Description
Filter Type OFF, LPF, HPF
Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
Cutoff Freq 200–8000 Hz Basic frequency of the filter
Pre Delay 0.0–100.0 ms
Adjusts the delay time from when
the direct sound begins until the
flanger sound is heard.
Rate 0.05–10.00 Hz, note Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180 deg Spatial spread of the sound
Feedback -98– +98%
Adjusts the proportion of the
flanger sound that is fed back into
the effect. Negative (-) settings will
invert the phase.
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Balance D100:0W–D0:100W
Volume balance between the direct
sound (D) and the flanger sound (W)
Level 0–127 Output Level
25: STEP FLANGER
Parameter Value Description
Filter Type OFF, LPF, HPF
Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
Cutoff Freq 200–8000 Hz Basic frequency of the filter
R in
R out
L in
L out
Flanger
Feedback
Feedback
Flanger
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
R in
R out
L in
L out
Feedback
Feedback
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
Step Flanger
Step Flanger
Pre Delay 0.0–100.0 ms
Adjusts the delay time from when
the direct sound begins until the
flanger sound is heard.
Rate 0.05–10.00 Hz, note Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180 deg Spatial spread of the sound
Feedback -98– +98%
Adjusts the proportion of the
flanger sound that is fed back into
the effect. Negative (-) settings will
invert the phase.
Step Rate 0.10–20.00 Hz, note Rate (period) of pitch change
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Balance D100:0W–D0:100W
Volume balance between the di-
rect sound (D) and the flanger
sound (W)
Level 0–127 Output Level
26: HEXA-CHORUS
Parameter Value Description
Pre Delay 0.0–100.0 ms
Adjusts the delay time from the di-
rect sound until the chorus sound is
heard.
Rate 0.05–10.00 Hz, note Frequency of modulation
Depth 0–127 Depth of modulation
Pre Delay
Deviation
0–20
Adjusts the differences in Pre Delay
between each chorus sound.
Depth
Deviation
-20– +20
Adjusts the difference in modulation
depth between each chorus sound.
Pan Deviation 0–20
Adjusts the difference in stereo loca-
tion between each chorus sound.
0: All chorus sounds will be in the
center.
20: Each chorus sound will be
spaced at 60 degree intervals
relative to the center.
Balance D100:0W–D0:100W
Volume balance between the direct
sound (D) and the chorus sound (W)
Level 0–127 Output Level
Parameter Value Description
Balance W
Balance W
L in
R in
L out
R out
Hexa Chorus
Balance D
Balance D
Prelude_e.book Page 65 Wednesday, January 14, 2009 2:18 PM