Filter
Top Products
70
Specifications for each Speaker Type
The speaker column indicates the diameter of each speaker unit (in
inches) and the number of units.
Flattens out high levels and boosts low levels, smoothing out
fluctuations in volume.
fig.MFX-40
Compresses signals that exceed a specified volume level, preventing
distortion from occurring.
fig.MFX-41
Cuts the reverb’s delay according to the volume of the sound sent into
the effect. Use this when you want to create an artificial-sounding
decrease in the reverb’s decay.
fig.MFX-42
Type Cabinet
Speak-
er
Micro-
phone
SMALL 1 small open-back enclosure 10 dynamic
SMALL 2 small open-back enclosure 10 dynamic
MIDDLE open back enclosure 12 x 1 dynamic
JC-120 open back enclosure 12 x 2 dynamic
BUILT-IN 1 open back enclosure 12 x 2 dynamic
BUILT-IN 2 open back enclosure 12 x 2 condenser
BUILT-IN 3 open back enclosure 12 x 2 condenser
BUILT-IN 4 open back enclosure 12 x 2 condenser
BUILT-IN 5 open back enclosure 12 x 2 condenser
BG STACK 1 sealed enclosure 12 x 2 condenser
BG STACK 2 large sealed enclosure 12 x 2 condenser
MS STACK 1 large sealed enclosure 12 x 4 condenser
MS STACK 2 large sealed enclosure 12 x 4 condenser
METAL STACK large double stack 12 x 4 condenser
2-STACK large double stack 12 x 4 condenser
3-STACK large triple stack 12 x 4 condenser
40: COMPRESSOR
Parameter Value Description
Attack 0–127 Sets the speed at which compression starts
Threshold 0–127
Adjusts the volume at which compression be-
gins
Post Gain 0– +18 dB Adjusts the output gain.
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Level 0–127 Output level
L in
R in
L out
R out
Compressor
2-Band EQ
2-Band EQ
Compressor
41: LIMITER
Parameter Value Description
Release 0–127
Adjusts the time after the signal volume falls
below the Threshold Level until compression
is no longer applied.
Threshold 0–127
Adjusts the volume at which compression be-
gins
Ratio
1.5:1, 2:1,
4:1,
100:1
Compression ratio
Post Gain 0– +18 dB Adjusts the output gain.
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Level 0–127 Output level
42: GATE
Parameter Value Description
Threshold 0–127
Volume level at which the gate begins to close
Mode
GATE,
DUCK
Type of gate
GATE: The gate will close when the vol-
ume of the original sound decreases, cut-
ting the original sound.
DUCK (Ducking): The gate will close when
the volume of the original sound increas-
es, cutting the original sound.
Attack 0–127
Adjusts the time it takes for the gate to fully
open after being triggered.
Hold 0–127
Adjusts the time it takes for the gate to start
closing after the source sound falls beneath
the Threshold.
Release 0–127
Adjusts the time it takes the gate to fully close
after the hold time.
Balance
D100:0W–
D0:100W
Volume balance between the direct sound
(D) and the effect sound (W)
Level 0–127 Output level
L in
R in
L out
R out
Limiter
2-Band EQ
2-Band EQ
Limiter
L in
R in
L out
R out
Gate
Gate
Prelude_e.book Page 70 Wednesday, January 14, 2009 2:18 PM