Filter
Top Products
DSP Algorithm List
E-88
DSP Algorithm List
J 00 :Auto Pan
Function
Continually performs left-right panning of the input
signal in accordance with an LFO.
Parameters
J 01 :Tremolo
Function
Adjusts volume of input signal in accordance with an
LFO.
Parameters
J 02 :2BandEQ
Function
This is a two-band equalizer.
Parameters
J 03 :3BandEQ
Function
This is a three-band equalizer.
Parameters
J 04 :LFO Wah
Function
This is a “wah” effect that can automatically affect the
frequency in accordance with an LFO.
Parameters
J 05 :Auto Wah
Function
This is a “wah” effect that can automatically affect the
frequency in accordance with the level of the input signal.
0 : Rate (Range: 0 to 127)
Adjusts the panning rate.
1 : Depth (Range: 0 to 127)
Adjusts the panning depth.
0 : Rate (Range: 0 to 127)
Adjusts the tremolo rate.
1 : Depth (Range: 0 to 127)
Adjusts the tremolo depth.
0 : Low Frequency (Range: 0 (200Hz), 1 (400Hz), 2
(800Hz))
Adjusts the cutoff frequency of the low-band
equalizer.
1 : Low Gain (Range: –12, –11, –10 to 0 to +10, +11,
+12)
Adjusts the gain of the low-band equalizer.
2 : High Frequency (Range: 0 (6.0KHz), 1
(8.0KHz), 2 (10KHz))
Adjusts the cutoff frequency of the high-band
equalizer.
3 : High Gain (Range: –12, –11, –10 to 0 to +10, +11,
+12)
Adjusts the gain of the high-band equalizer.
0 : Low Frequency (Range: 0 (200Hz), 1 (400Hz), 2
(800Hz))
Adjusts the cutoff frequency of the low-band
equalizer.
1: Low Gain (Range: –12, –11, –10 to 0 to +10, +11,
+12)
Adjusts the gain of the low-band equalizer.
2: Mid Frequency (Range: 0 (1.0KHz), 1 (1.3KHz),
2 (1.6KHz), 3 (2.0KHz), 4 (3.0KHz), 5 (4.0KHz),
6 (6.0KHz), 7 (8.0KHz))
Adjusts the center frequency of the mid-band
equalizer.
3: Mid Gain (Range: –12, –11, –10 to 0 to +10, +11,
+12)
Adjusts the gain of the mid-band equalizer.
4: High Frequency (Range: 0 (6.0KHz), 1
(8.0KHz), 2 (10KHz))
Adjusts the cutoff frequency of the high-band
equalizer.
5: High Gain (Range: –12, –11, –10 to 0 to +10, +11,
+12)
Adjusts the gain of the high-band equalizer.
0: Input Level (Range: 0 to 127)
Adjusts the input level. The input signal can
become distorted when the level of the sound
being input, the number of chords, or the
Resonance value is large. Adjust this parameter
to eliminate such distortion.
1: Resonance (Range: 0 to 127)
Adjusts the resonance of the sound.
2: Manual (Range: 0 to 127)
Adjusts the frequency used as the basis for the
wah filter.
3: LFO Rate (Range: 0 to 127)
Adjusts the rate of the LFO.
4: LFO Depth (Range: 0 to 127)
Adjusts the depth of the LFO.
705A-E-090A