Filter
Top Products
41
Sequencer
Tone Adjust pages have been added to Sequencer P5: Track
Edit (☞PG p.68).
5–3: Tone1.2 1–8 (Tone1/2 T01–08)
5–4: Tone1.2 9–16 (Tone1/2 T09–16)
5–5: Tone3.4 1–8 (Tone3/4 T01–08)
5–6: Tone3.4 9–16 (Tone3/4 T09–16)
5–7: Tone5.6 1–8 (Tone5/6 T01–08)
5–8: Tone5.6 9–16 (Tone5/6 T09–16)
In the Tone Adjust pages you can make adjustments to the
sound of the program assigned to each track. While creating
a song, you can make adjustments to the sounds without
having to return to Program mode. For example, you might
make the bass slightly mellower, or sharpen the attack of the
strings to better suit the song. The sound is changed only in
the song; the original program memory remains unchanged.
You can also record and play back exclusive events
(☞p.34) using these parameters to modify sounds in
realtime as the song plays.
A total of 25 parameters are available, and up to six (e.g., fil-
ter cutoff, resonance, filter EQ, amp EG) may be assigned to
each track.
5–1(2)(3)(4)(5)(6)a: Tone Adjust 1–Tone Adjust 6
Destination [LPF Cutoff...Reverse]
Assigns a parameter to each of the Tone Adjust controls.
Value [–99...+99, –199...+199, –12.00...+12.00,
–1200...+1200, Off...On]
Specifies the value of the parameter selected in “Destina-
tion.” If this is set to +00 or PRG, the value specified by the
program will be used.
Normally you would not select the same parameter for
more than one “Destination” in the same track. How-
ever if you do, the results will be as follows.
For parameters other than Hold and Reverse
If the same parameter is selected for more than one
“Destination” on an single track, the “Value” will be
summed. However, the “Value” of the “Destination”
parameter can not exceed the range of possible values.
For example if you have made three assignments for
Detune 1 on the same track, and the settings of these
three are +1000, +1000, and +1000, the Detune 1 param-
eter will actually be at +1200. (The total is +3000 but the
result is limited to the Detune 1 parameter’s maximum
value of +1200.) If the three settings are +1000, +1000,
and –1000, the Detune 1 parameter will have an actual
value of +1000.
Hold and Reverse
The most recently made settings will apply.
“Destination” and “Value”
You can choose any of the following parameters as a “Desti-
nation,” and the value can be set within the ranges listed
below.
LPF Fc (LPF Cutoff) [–99...+00...+99]
Adjusts the OSC 1/2 low pass filter cutoff frequency. Adjust-
ing this will vary the brightness of the sound. This controls
the same parameter as when CC#74 is received. (☞PG p.256,
INT-F bank: EM p.10)
Reso HPF (Resonance/HPF Cutoff) [–99...+00...+99]
Adjusts the OSC 1/2 low pass filter resonance level or high
pass filter cutoff frequency. The setting that will actually be
controlled will depend on the filter type specified by the
program. This controls the same parameter as when CC#71
is received. (☞PG p.256, INT-F bank: EM p.10)
F EG Int (Filter EG Intensity) [–99...+00...+99]
Adjusts the program OSC 1/2 filter EG intensity (the depth
to which the filter EG is applied). This controls the same
parameter as when CC#79 is received. (☞PG p.257, INT-F
bank: EM p.10)
Amp Vel I (Amp Velocity Intensity) [–99...+00...+99]
Adjusts the program OSC 1/2 amp velocity intensity (the
depth to which velocity will affect the amp). This controls
the Amp Modulation “Velocity Intensity” (4–2b ☞PG p.22)
For an INT-F bank program, this controls the Amp EG
Level Modulation “Velocity Control” (☞EM p.42)
F/A EG A (Filter/Amp EG Attack) [–99...+00...+99]
Adjusts the program OSC 1/2 filter EG and amp EG attack
times. In order to maximize the effect of the adjustment, the
amp EG start level, attack level, start level modulation, and
attack time modulation will also be adjusted simultaneously.
This controls the same parameter as when CC#73 is
received. (☞PG p.256, INT-F bank: EM p.10)
F/A EG D (Filter/Amp EG Decay) [–99...+00...+99]
Adjusts the program OSC 1/2 filter EG and amp EG decay
times. This controls the same parameter as when CC#75 is
received. (☞PG p.256, INT-F bank: EM p.10)
F/A EG S (Filter/Amp EG Sustain) [–99...+00...+99]
Adjusts the program OSC 1/2 filter EG and amp EG sustain
levels. This controls the same parameter as when CC#70 is
received. (☞PG p.256, INT-F bank: EM p.10)
F/A EG R (Filter/Amp EG Release) [–99...+00...+99]
Adjusts the program OSC 1/2 filter EG and amp EG release
times. This controls the same parameter as when CC#72 is
received. (☞PG p.256, INT-F bank: EM p.10)
Tone Adjust Parameters
5–1a