Filter
Top Products
116
Chapter 8 Parameters Guide FX (Effects)
MOD1, MOD2
For MOD1 and MOD2, you can choose one of the following effect
types. (If desired, you can select the same effect for both MOD1 and
MOD2.)
PHASER
By adding varied-phase portions to the direct sound, the phaser
effect gives a whooshing, swirling character to the sound.
MOD TYPE
MOD1
MOD2
Common
PHASER Phaser (p. 116)
FLANGR Flanger (p. 117)
TREML Tremolo (p. 117)
PAN Pan (p. 117)
PEDAL WAH Pedal Wah (p. 118)
T.WAH Touch Wah (p. 118)
AUTO WAH Auto Wah (p. 119)
M-TRON III M-TRON III (p. 119)
OCTAVE Octave (p. 120)
PITCH SHIFT Pitch Shifter (p. 120)
HARMONIST Harmonist (p. 121)
PEDAL BEND Pedal Bend (p. 122)
2x2 CHORUS 2x2 Chorus (p. 122)
ROTARY Rotary (p. 123)
UNI-V Uni-V (p. 123)
VIB Vibrato (p. 123)
SLICER Slicer (p. 123)
HUMANIZER Humanizer (p. 124)
SLOW GEAR Slow Gear (p. 124)
RING MOD Ring Modulator (p. 124)
ANTI FB Anti Feedback (p. 124)
ADV.COMP Advanced Compressor (p. 125)
LIMITR Limiter (p. 125)
ENHANCER Enhancer (p. 125)
PEQ Parametric Equalizer (p. 126)
GEQ Graphic Equalizer (p. 126)
SUB DELAY Sub Delay (p. 126)
Parameter/
Range
Explanation
MOD1 SW, MOD2 SW
OFF, ON Turns the MOD-1 (MOD-2) effect on/off.
MOD 1 TYPE, MOD 2 TYPE
see above Selects the effect to be used.
Parameter/
Range
Explanation
TYPE
Selects the number of stages that the phaser effect will use.
4STG This is a four-phase effect. A light phaser ef-
fect is obtained.
8STG This is an eight-phase effect. It is a popular
phaser effect.
12STG This is a twelve-phase effect. A deep phase
effect is obtained.
BI-PHS This is the phaser with two phase shift cir-
cuits connected in series.
RATE
0–100,
BPM –BPM
This sets the rate of the phaser effect.
When set to BPM, the value of each parameter will be set according
to the value of the BPM (p. 142) specified for each patch. This makes
it easier to achieve effect sound settings that match the tempo of the
song.
* If, due to the tempo, the time is longer than the range of allowable
settings, it is then synchronized to a period either 1/2 or 1/4 of that
time.
DEPTH
0–100
Determines the depth of the rotation effect.
MANUAL
0–100
Adjusts the center frequency of the rotation
effect.
RESO (Resonance)
0–100
Determines the amount of resonance (feed-
back).
Increasing the value will emphasize the ef-
fect, creating a more unusual sound.
STEP RATE
OFF, 0–100,
BPM –BPM
This sets the cycle of the step function that
changes the rotation. When it is set to a high-
er value, the change will be finer. Set this to
Off when not using the Step function.
When set to BPM, the value of each parameter will be set according
to the value of the BPM (p. 142) specified for each patch. This makes
it easier to achieve effect sound settings that match the tempo of the
song.
* If, due to the tempo, the time is longer than the range of allowable
settings, it is then synchronized to a period either 1/2 or 1/4 of that
time.
EFFECT LEVEL
0–100
Adjusts the volume of the phaser.
DIRECT LEVEL
0–100
Adjusts the volume of the direct sound.
VB-99_e.book 116 ページ ２００８年８月１８日 月曜日 午後１時１０分