Filter
Top Products
23
To Control the Projector Whose Protocol Is Not Preset to the Mixer
b Enter 1 in the WAIT1 input box and enter 9 in the
WAIT2 input box, then adjust the wait time during
later operation check.
5
Operation check by using the TEST button
a Select VIDEO using the PROJECTOR INPUT
SELECT button without inputting any signals to
AV/RGB INPUT connectors of the mixer, then
click the TEST button on the PROTOCOL
SETTING screen.
b Check that VIDEO is selected as the input signal
on the projector.
c Do steps a and b for all other signal formats.
If the input selection on the projector is not performed
correctly, check that the commands entered in the
command input section and the port setting are
correct.
After confirming the commands and the port setting,
repeat the step 5 above by increasing the wait time to
be input to the WAIT1 input box in 1-second steps
until the projector operates correctly.
6
Operation check by using the AV/RGB
SELECT buttons on the mixer
a Click one of the SIGNAL DEFINE selection radio
buttons on the PARALLEL/PROJECTOR
CONTROL screen to make the setting for actual
use.
b Input signals from all the AV/RGB INPUT
connectors on the mixer, and press the AV/RGB
SELECT buttons on the mixer to check that the
video signal is output to the projector.
c Press the AV/RGB SELECT buttons to check all
operation patterns (A t B, A t C, A t D, A
t E, ..... E t A, E t B, E t C, and E t D)
to check that the video signal is output to the
projector.
d Press the AV/RGB SELECT buttons several times
at random to check that the video signal
corresponding to the button which has been
pressed the last is output to the projector.
e Repeat the step d more than ten times.
When the video signal is not output to the projector,
check the settings of the SIGNAL DEFINE selection
radio buttons on the PARALLEL/PROJECTOR
CONTROL screen and the settings on the projector.
After confirming the settings above are correct, do the
steps below to adjust the wait time.
a Increase the wait time to be input to the WAIT1
and 2 input boxes at the same time in 1-second
steps until the projector operates correctly.
b Decrease the wait time to be input to the WAIT1
input box in 1-second steps until the projector
operates correctly.
c Decrease the wait time to be input to the WAIT2
input box in 1-second steps until the projector
operates correctly.
If you want to shorten the time to take for the video
signal is output to the projector after pressing the AV/
RGB SELECT buttons on the mixer, set the wait time
for the WAIT1 and 2 input boxes to the shortest time
first. Then perform “5 Operation check by using the
TEST button” and “6 Operation check by using the
AV/RGB SELECT buttons on the mixer”.
7
Operation check to turn on the projector
a Press the AV/RGB SELECT A button on the
mixer and check that the video signal is output to
the projector.
b Operate the input signal selector on the projector
so that no video signal is output to the projector.
c Press the POWER switch on the projector to place
it to standby status.
d After confirming that the projector is in standby
status, click the TEST button in the PROJECTOR
POWER ON section on the PROTOCOL
SETTING screen.
e Check that the projector turns on and the video
signal output to the AV/RGB INPUT connector is
input to the projector.
f Repeat the steps a to e for the AV/RGB
SELECT B-E buttons.
When the projector does not turn on, check that the
command entered in the command input section is
correct.
When the video signal is not output to the projector,
repeat the test by increasing the wait time to be input
to the WAIT input box in 1-second steps until the
projector operates correctly.
If you want to shorten the time to take for the video
signal is output after the projector turns on, repeat the
test by decreasing the wait time to be input to the
WAIT input box in 1-second steps until the projector
operates correctly.
8
Operation check to set the projector to
standby status
COMPONENT COMPONENT signal
selection command
COMPONENT/RGB
input terminal select
command
OTHER
TERMINAL
Undefined (blank) Undefined (blank)