Filter
Top Products
23
En
Operation
— [ ]: Set here for a curve that rises gradually.
— [ ]: Set here for a curve that rises steeply. (When the crossfader
moves away from either the left or right edge, the sound is imme-
diately output from the opposite side.)
5 Set the crossfader.
Switch the channel whose sound is output from the speakers.
— Left edge: The [CH 1] sound is output.
— Center position: The sound of [CH 1] and [CH 2] is mixed and
output.
— Right edge: The [CH 2] sound is output.
! This operation is not necessary when the [CROSS F. CURVE (THRU,
, )] selector switch is set to [THRU].
6 Turn the [MASTER LEVEL] control clockwise.
Sound is output from the speakers.
The [LEVEL] indicator lights.
Adjust the [MASTER LEVEL] control so that the orange indicator lights
where the track’s volume is highest (at the climax, etc.).
Be careful that the red indicator does not light, or the sound could be
distorted.
Mixing using the faders
Prepare the unit in advance so that the sound of [CH 1] is being output
from the speakers. For instructions on preparation, see Outputting
sound on page 22.
For instructions on monitoring the sound, see Monitoring sound with
headphones on page 19.
Mixing using the channel faders
1 Set [CROSS F. CURVE THRU, , ] (the crossfader
curve selection switch) to [THRU].
2 Switch the [DECK 2, PHONO2/LINE2] selector switch in
the [CH 2] section.
3 Turn the [TRIM] control in the [CH 2] section
clockwise.
4 Press the [ (CH2)] button.
The sound of [CH 2] is monitored from the headphones.
5 Turn the [HEADPHONES MIXING] control.
This adjusts the balance of the monitor volume between the sound
output from the [MASTER OUT 1] and [MASTER OUT 2] terminals (the
sound of [CH 1]) and the sound of [CH 2].
6 Operate [DECK 2].
While checking the sound over the headphones, adjust the tempo of
[CH 2] track to match the tempo of [CH 1] track.
7 While moving the [CH 2] channel fader to the back,
move the [CH 1] channel fader to the front.
While checking the sound output from the speakers, operate the chan-
nel faders to substitute the sound of [CH 1] with the sound of [CH 2].
Mixing is completed once only the [CH 2] sound is being output from the
speakers.
Mixing using the crossfader
1 Set [CROSS F. CURVE THRU, , ] (the crossfader
curve selector switch) to [ ] or [ ].
2 Operate [CH 2].
Perform steps 2 to 6 at Mixing using the channel faders above.
3 Move the crossfader gradually to the right.
While checking the sound output from the speakers, operate the cross-
fader to substitute the sound of [CH 1] with the sound of [CH 2].
Mixing is completed once only the [CH 2] sound is being output from the
speakers.
Using the QUANTIZE function
This function can be used to play auto beat loops, apply beat effects,
etc., in tempo with the currently playing track based on the track’s GRID
information as analyzed with rekordbox.
! Music files must be analyzed ahead of time with rekordbox in order
to use the QUANTIZE function. For instructions on analyzing music
files with rekordbox, see the rekordbox Operating Instructions.
Press the [TIME (AUTO CUE, QUANTIZE)] button while
pressing the [SHIFT] button.
The QUANTIZE function turns on.
When the QUANTIZE function is turned on, the points are automatically
set to the nearest beat position when auto beat loops, beat effects, cues
or hot cues are set.
Furthermore, the auto beat loop, beat effect, hot cue and other functions
can be used without breaking the beat.
! When the [TIME (AUTO CUE, QUANTIZE)] button is pressed again
while pressing the [SHIFT] button, the QUANTIZE function turns off.
Using the SYNC function
This function can be used to automatically synchronize the tempo (BPM)
and beat positions on the left and right decks based on the tracks’ GRID
information as analyzed with rekordbox.
! Music files must be analyzed ahead of time with rekordbox in order
to use the SYNC function. For instructions on analyzing music files
with rekordbox, see the rekordbox Operating Instructions.
! The following describes the procedure for synchronizing the
[DECK 2] track to the [DECK 1] track.
1 Play a track that has been analyzed with rekordbox
on [DECK 1].
The deck on which a track that has been analyzed with rekordbox is
played first is set as the MASTER for the SYNC function.
! The master can also be specified by pressing the [MASTER] button.
2 Play a track that has been analyzed with rekordbox
on [DECK 2].
3 Press the [SYNC] button for [DECK 2].
[DECK 2] is synchronized to the tempo (BPM) and beat positions of the
track playing on [DECK 1].
! When the [SYNC] button is pressed again, the SYNC function turns
off.
! Use the procedure below to restore the currently playing track’s
tempo (BPM) to its original tempo after turning the SYNC function
off.
— First move the [TEMPO] slider to the position to which the tempo
(BPM) was synchronized (the [TEMPO] indicator turns off), then
move it back to the center position.
— Reload the same track.
! Depending on the track’s beat information, the sound may not be
synchronized after the [SYNC] button is pressed. If this happens, the
sound can be re-synchronized by pressing the [SYNC] button to turn
the sync mode off then back on.