Filter
Top Products
Making Global Settings (System Settings)
41
Quick Guide Overview Outputting Sound Eects Saving
Pedal Settings
System MIDI/USB Appendices
Item Parameter Value Explanation
PLAY OPTION
Making the PLAY OPTION Settings
Here you can specify how the pedals will work during performance.
BANK CHANGE
MODE
WAIT
Although the indication in the display is updated to reect the change in the bank when a BANK
pedal is pressed, the patch will not change until a number pedal has been pressed.
IMMED The patch switches instantly when a BANK pedal or any of the number pedals is pressed.
EXP PEDAL HOLD
OFF The operational status of the EXP PEDAL’s FUNC (p. 34) is not carried over when patches are switched.
ON
If the EXP PEDAL’s FUNC (p. 34) are the same between 2 patches, the operational status is carried over
when patches are switched.
For example, if EXP PEDAL FUNC is set to FOOT VOLUME in both patches, the one before and the
one after the change, the volume corresponding to the position the pedal is in (angle) at the time of
the patch change will be maintained after the patch change. On the other hand, if the patch being
changed to is set to WAH, the volume will be in accordance with the value set within the patch, and
you’ll obtain a wah eect that is in accordance with a value that reects the current position (angle)
of the pedal.
KNOB LOCK OFF, ON Species whether knob operations will be disabled. If this is ON, knob operations will be disabled.
NUM PEDAL SW
OFF, TUNER, Ch.A/B, OD
SOLO, A/B SOLO,
A&B SOLO
Selects the function that will be recalled when you press the pedal of the same number as the
currently selected patch (p. 35).
BANK EXTENT MIN U01–U50, P01–P50 Sets the lower limit for the banks.
BANK EXTENT MAX U01–U50, P01–P50 Sets the upper limit for the banks.
PEDAL INDICAT OFF, ON If this is ON, all currently unlit pedal indicators will blink dimly.
KNOB SETTING
Assigning the [1]–[8] Knob Functions in the Play Screen
Here you can assign the desired parameters to knobs [1]–[8] in the Play Screen (p. 35).
* The settings you make here are only for the knobs in the Play Screen.
KNOB 1
OFF, parameter name
For details on all parameters, refer to the “GT-100 Parameter Guide” (PDF le) which you can download
from the Roland website (http://www.roland.com/support/en/) under “GT-100” in the list of “Owner’s
Manuals.”
KNOB 2
KNOB 3
KNOB 4
KNOB 5
KNOB 6
KNOB 7
KNOB 8
PREFERENCE
Specifying Whether Settings Will Be Shared by All Patches
Here you can specify whether settings for the type of connected amp and preamp, control pedal, expression pedal, etc. will be independent for each
patch, or whether the same settings will be shared by all patches.
OUTPUT SELECT PATCH, SYSTEM
If this is set to PATCH, dierent settings can be made independently for each patch. If this is set to
SYSTEM, the same settings will be shared by all patches.
* Here, even if a CTL/EXP pedal that has been set to SYSTEM is set to ASSIGN SOURCE (p. 37), that
setting will be ignored. In the case of the ACCEL/CTL pedal, in addition to the above, settings for
Manual mode (p. 17) will also be ignored.
PREAMP PATCH, SYSTEM1–3
ACCEL/CTL PATCH, SYSTEM
EXP PATCH, SYSTEM
EXP SW PATCH, SYSTEM
SUB CTL1 PATCH, SYSTEM
SUB CTL2 PATCH, SYSTEM
SUB EXP PATCH, SYSTEM
LCD
Adjusting the Contrast (Brightness) of the LCD Screen
Here you can adjust the brightness of the characters in the display.
CONTRST LEFT
1–16 Higher values increase the brightness.
CONTRST RIGHT
PEDAL CALIBRATION
Adjusting the [EXP] pedal
You can readjust the [EXP] pedal so that it will operate optimally. Refer to “Adjusting the [EXP] pedal” (p. 36).
THRESHOLD 1–16 Adjusts the sensitivity at which the EXP PEDAL SW will respond.