Filter
Top Products
129
Effects
Chorus, Flanger, and Phaser (Cho/Fln Phaser)
Advanced
41: Stereo Phaser
This effect creates a swell by shifting the phase. It is very effective
on electric piano sounds. You can add spread to the sound by
offsetting the phase of the left and right LFOs from each other.
h: Resonance
i: Wet/Dry
The peak shape of the positive and negative Feedback value is
different. The harmonics will be emphasized when the effect
sound is mixed with the dry sound, if you set a positive value for
both “Resonance” and “Wet/Dry”, and if you set a negative value
for both “Resonance” and “Wet/Dry”.
h: High Damp [%]
This parameter sets the amount of damping of the resonance in
the high range. Increasing the value will cut high-range harmon-
ics.
42: Orange Phaser
This models a standard model of analog phaser that achieved
great popularity. It gives a sense of movement to electric piano
sounds, adding a rich-sounding phase shift effect.
43: Small Phaser
This models a classic phaser that was born in New York during
the 1970s. With a warm, rich tone, it is also loved by many elec-
tric piano players.
Color
This lets you choose between two types of phaser sound. Turn-
ing this On produces a deeper phase shift effect with a distinc-
tive modulation.
a
LFO Waveform Triangle, Sine Selects the LFO Waveform
LFO Shape –100...+100
Changes the curvature of the LFO
Waveform
b
LFO Phase
[degree]
–180...+180
Sets the LFO phase difference
between the left and right
c
LFO Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
Src Off...Tempo
Selects a modulation source for LFO
speed
Amt
–20.00...
+20.00
Sets the modulation amount of LFO
speed
d
MIDI Sync Off, On
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Base Note r...w
Selects the type of notes that
specify the LFO speed
Times x1...x32
Sets the number of notes that
specify the LFO speed
e
Manual 0...100
Sets the frequency to which the
effect is applied
Src Off...Tempo
Selects the modulation source for
the LFO modulation
Amt –100...+100
Sets the modulation amount of the
LFO modulation
f
Depth 0...100 Sets the depth of LFO modulation
Src Off...Tempo
Selects the modulation source for
the LFO modulation depth
Amt –100...+100
Sets the modulation amount of the
LFO modulation depth
h
Resonance –100...+100
Sets the resonance amount
High Damp [%] 0...100
Sets the resonance damping
amount in the high range
j
Wet/Dry
-Wet, -
1:99...Dry...99:1
, Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
Left
Right
Resonance
LFO Shape
LFO Phase
LFO: Tri / Sine
FX Amt
FX Amt
High Damp
Stereo In - Stereo Out
Phaser
Phaser
Speed [Hz] 0.10...10.0 Sets the speed of the LFO
Color Off, On
Switches the tone of the phaser sound
page 129
Wet/Dry
–Wet...
–1 : 99, Dry,
1 : 99...Wet
Balance between the wet and dry signal
page 115, page 129
Source Off...Tempo
Table , “Selects a modulation source for Wet/
Dry,” on page 107
Amount –100...+100
Table , “Sets the modulation amount for Wet/
Dry,” on page 107
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Phaser
LFO
Color