Filter
Top Products
179
Effects
Double Size
Advanced
The effect is off when a value for the modulation source specified for
the “RST Control Src” parameter is 63 or smaller, and the effect is on
when the value is 64 or higher.
137: LCR BPM Long Dly
The L/C/R delay enables you to match the delay time with the
song tempo.
a: Time Over?
You can set the delay time up to 10,920msec. If the delay time
exceeds this limit, the error message “OVER!” appears in the dis-
play. Set the delay time parameters so that this message will not
appear. “Time Over?” is only a display parameter.
138: St. BPM Long Dly
(Stereo BPM Long Delay)
The stereo delay enables you to match the delay time with the
song tempo.
a: Time Over? L, R
You can set the delay time up to 5,460msec. If the delay time
exceeds this limit, the error message “OVER!” appears in the dis-
play. Set the delay time parameters so that this message will not
appear. “Time Over?” is only a display parameter.
a
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Time Over? ---, OVER!
Displays an error message when the
delay time exceeds the upper limit
b
L Delay Base
Note
r...w
Selects the type of notes to specify
the delay time for TapL
Times x1...x32
Sets the number of notes to specify
the delay time for TapL
Level 0...50 Sets the output level of TapL
c
C Delay Base
Note
r...w
elects the type of notes to specify
the delay time for TapC
Times x1...x32
Sets the number of notes to specify
the delay time for TapC
Level 0...50 Sets the output level of TapC
d
R Delay Base
Note
r...w
Selects the type of notes to specify
the delay time for TapR
Times x1...x32
Sets the number of notes to specify
the delay time for TapR
Level 0...50 Sets the output level of TapR
e
Feedback
(C Delay)
–100...+100 Sets the feedback amount of TapC
Src Off...Tempo
Selects the modulation source for
the TapC feedback
Amt –100...+100
Sets the modulation amount of the
TapC feedback
f
High Damp [%] 0...100
Sets the damping amount in the
high range
Low Damp [%] 0...100
Sets the damping amount in the low
range
g
Input Level
Dmod [%]
–100...+100
Sets the modulation amount of the
input level
Src Off...Tempo
Selects the modulation source for
the input level
h Spread 0...50
Sets the width of the stereo image
of the effect sound
i
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
C Delay
R Delay
Left
Right
Feedback
Spread
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In -Stereo Out
Input Level D-mod
High Damp
Low Damp
L Delay
Input Level D-mod
+
Level
Level
Level
Tempo
BPM
BPM
Base Note x Times
Base Note x Times
Base Note x Times
a
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Time Over? L ---, OVER!
Display the error message if the left
channel delay time exceeds the
upper limit
R ---, OVER!
Display the error message if the
right channel delay time exceeds
the upper limit
b
L Delay Base
Note
r...w
Selects the type of notes to specify
the left channel delay time
Times x1...x32
Sets the number of notes to specify
the left channel delay time
Adjust [%] –2.50...+2.50
Fine-adjust the left channel delay
time
c
R Delay Base
Note
r...w
Selects the type of notes to specify
the right channel delay time
Times x1...x32
Sets the number of notes to specify
the right channel delay time
Adjust [%] –2.50...+2.50
Fine-adjust the right channel delay
time
d
L Feedback –100...+100
Sets the feedback amount for the
left channel
Src Off...Tempo
Selects the modulation source of
feedback amount
L Amt –100...+100
Sets the modulation amount of the
left channel feedback
e
R Feedback –100...+100
Sets the feedback amount for the
right channel
R Amt –100...+100
Sets the modulation amount of the
right channel feedback
f High Damp [%] 0...100
Sets the damping amount in the
high range
g Low Damp [%] 0...100
Sets the damping amount in the low
range
h
Input Level
Dmod [%]
–100...+100
Sets the modulation amount of the
input level
Src Off...Tempo
Selects the modulation source for
the input level
i
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
Left
Right
Feedback
FX Amt
FX Amt
Stereo In - Stereo Out
Input Level D-mod
Input Level D-mod
High Damp Low Damp
High Damp
Low Damp
Tempo
BPM
BPM
Base Note x Times
Adjust [%]
Base Note x Times
Adjust [%]
Delay
Delay