Filter
Top Products
162
Effects
Mono-Mono Serial (Mono-Mono)
103: Limiter - Mt.Delay
(Limiter - Multitap Delay)
This effect combines a mono limiter and a multitap delay. You
can change the order of the effects.
104: Exciter - Comp
(Exciter -Compressor)
This effect combines a mono exciter and a compressor. You can
change the order of the effects.
LIMITER
a
[L]Ratio
1.0 : 1...
50.0 : 1, Inf : 1
Sets the signal compression ratio
Threshold [dB] –40...0
Sets the level above which the
compressor is applied
b
[L]Attack 1...100 Sets the attack time
Release 1...100 Sets the release time
c
[L]Gain Adjust
[dB]
–Inf,
–38...+24
Sets the limiter output gain
MULTITAP DELAY
d
[D]Tap1 Time
[msec]
0.0...1360.0 Sets the Tap1 delay time
Tap1 Level 0...100 Sets the Tap1 output level
e
[D]Tap2 Time
[msec]
0.0...1360.0 Sets the Tap2 delay time
Feedback –100...+100 Sets the Tap2 feedback amount
f
[D]High Damp
[%]
0...100
Sets the damping amount in the
high range
g
[D]Mt.Delay
Wet/Dry
Dry, 1:99...99:1,
Wet
Sets the multitap delay effect
balance
Src Off...Tempo
Selects the multitap delay’s Wet/Dry
modulation source
Amt –100...+100
Sets the multitap delay’s Wet/Dry
modulation amount
hRouting
Limiter
Mt.Delay,
Mt.Delay
Limiter
Switches the order of the limiter and
multitap delay
i
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
+
Routing
Multitap Delay
Feedback
High Damp
Delay
(2)
(1)
Mt.Dly FX Amt
Limiter
Limiter
Gain Adjust
Envelope - Control
EXCITER
a
[X]Exciter
Blend
–100...+100
Sets the intensity (depth) of the
Exciter effect
b
[X]Emphasis
Frequency
0...70
Sets the frequency range to be
emphasized
c [X]EQ Trim 0...100 Sets the EQ input level
d
[X]Pre LEQ
Gain [dB]
–15...+15 Sets the gain of Low EQ
Pre HEQ Gain
[dB]
–15...+15 Sets the gain of High EQ
COMPRESSOR
e
[C]
Sensitivity
1...100 Sets the sensitivity
f
[C]Attack 1...100 Sets the attack level
Output Level 0...100 Sets the compressor output level
gRouting
Exciter Comp,
Comp Exciter
Switches the order of the exciter and
compressor
h
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
+
Routing
Compressor
LEQ HEQ
EQ Trim
Comp
Output Level
Envelope - Control
Exciter
Exciter