Filter
Top Products
53
About V-LINK
You can set or edit the following functions that are related to V-LINK. With the exception of the pad mode, make the setting and
then press [SAMPLING] to save the setting.
Devices such as the Edirol PR-50/80 use only V-LINK Ctrl Ach.
*1 For details on the functions that can be controlled, refer to
“Functions that you can control using CTRL 1–3 and D Beam”
(p. 52).
V-LINK settings
Function Value (display indi-
cation)
Operation Remarks
Pad mode
Clip/Palette
(“CLP”, “PLT”)
[V-LINK] + [EFFECT MEMORY] Fixed at Clip at power-on.
V-LINK Ctrl
Ach
1 – 16
(“C. 1”–“C.16”)
[CANCEL] + [V-LINK]
➜
Bank[A]
➜
CTRL 3 knob (can also change using
pad [1]–[16])
Specifies the MIDI channel that will control section A of mo-
tion dive .tokyo. The factory setting is channel 4.
V-LINK Ctrl
Bch
1 – 16
(“C. 1”–“C.16”)
[CANCEL] + [V-LINK]
➜
Bank[B]
➜
CTRL 3 knob (can also change using
pad [1]–[16])
Specifies the MIDI channel that will control section B of motion
dive .tokyo. The factory setting is channel 10.
V-LINK Ctrl
Cch
1 – 16
(“C. 1”–“C.16”)
[CANCEL] + [V-LINK]
➜
Bank[C/G]
➜
CTRL 3 knob (can also change us-
ing pad [1]–[16])
Specifies the MIDI channel that will control the MIDI Note
plug-in of motion dive .tokyo. The factory setting is channel 9.
CTRL 1 Assign
(*1)
Off, 1 – 30
(“oFF”, “ 1”–“30”)
[CANCEL] + [V-LINK]
➜
Sw below
CTRL 1
➜
CTRL 3 knob
Assigns a V-LINK function to CTRL 1. The factory setting is 4
(Speed Knob).
CTRL 2 Assign
(*1)
Off, 1 – 30
(“oFF”, “ 1”–“30”)
[CANCEL] + [V-LINK]
➜
Sw below
CTRL 2
➜
CTRL 3 knob
Assigns a V-LINK function to CTRL 2. The factory setting is 2
(ColorEQ Back).
CTRL 3 Assign
(*1)
Off, 1 – 30
(“oFF”, “ 1”–“30”)
[CANCEL] + [V-LINK]
➜
Sw below
CTRL 3
➜
CTRL 3 knob
Assigns a V-LINK function to CTRL 3. The factory setting is 6
(Cross Fader).
D Beam As-
sign (*1)
Off, 1 – 30
(“oFF”, “ 1”–“30”)
[CANCEL] + [V-LINK]
➜
[SYNTH]/
[FILTER]/[TRIGGER]
➜
CTRL 3 knob
Assigns a V-LINK function to D Beam. The factory setting is 1
(ColorEQ Fore).
Seq Ach Ctrl
Pad Bank
Off, Bank A – J
(“off”, “b. A”–“b. J”)
[CANCEL] + [V-LINK]
➜
Bank[D/H]
➜
CTRL 3 knob
Of the pad information included in the pattern data, the infor-
mation of the specified bank will be used to control section A
of motion dive .tokyo. The factory setting is bank A.
Seq Bch Ctrl
Pad Bank
Off, Bank A – J
(“off”, “b. A”–“b. J”)
[CANCEL] + [V-LINK]
➜
Bank[E/I]
➜
CTRL 3 knob
Of the pad information included in the pattern data, the infor-
mation of the specified bank will be used to control section B
of motion dive .tokyo. The factory setting is bank B.
Seq Cch Ctrl
Pad Bank
Off, Bank A – J
(“off”, “b. A”–“b. J”)
[CANCEL] + [V-LINK]
➜
Bank[F/J]
➜
CTRL 3 knob
Of the pad information included in the pattern data, the infor-
mation of the specified bank will be used to control the MIDI
Note plug-in of motion dive .tokyo. The factory setting is bank
C.
V-LINK Sw
Mode
Standerd, MD-P1
(“Std”, “MdP”)
[CANCEL] + [V-LINK]
➜
[FIXEDVE-
LOCITY]
➜
CTRL 3 knob
Specifies what will happen when V-LINK is turned on/off.
With the “Standard” setting, only a V-LINK On/Off message
will be transmitted. With the “MD-P1” setting, a Reset Ctrl Pa-
rameters message will be transmitted when V-LINK is turned
on, and a message that sets Total Fader to 0 will be transmit-
ted when V-LINK is turned off. The factory setting is MD-P1.
SP-555_e.book 53 ページ ２００７年６月２５日 月曜日 午前９時９分