Filter
Top Products
55
Appendix
MFX bank A
Number
Type CTRL 1 function (display) CTRL 2 function (display) CTRL 3 function (display)
1
FLANGER DEPTH (dPt) RATE (rAt) FEEDBACK (Fdb)
✩
Creates modulation reminis-
cent of a jet airplane taking
off and landing.
Adjusts the depth of modula-
tion.
Adjusts the speed of modula-
tion.
Adjusts the proportion of effect
sound that is returned to the in-
put.
2 PHASER DEPTH (dPt)
✩
RATE (rAt)
MANUAL (MAn)
Creates modulation by add-
ing a phase-shifted sound.
Adjusts the depth of modula-
tion.
Adjusts the speed of modula-
tion.
Adjusts the pitch of the effect
sound.
3 WAH PEAK (PEk) RATE (rAt) MANUAL (MAn)
Produces a wah effect. Adjusts the width of frequencies
to which effect is applied.
Adjust the speed of modulation. Adjusts the pitch of the effect
sound.
4 TREMOLO/PAN DEPTH (dPt) RATE (rAt) WAVEFORM (trM/PAn)
Cyclically varies the volume
or panning.
Adjusts the amount of change in
volume/panning.
Adjusts the speed of volume/
panning change.
Specifies the volume/panning
modulation curve. Turn knob to
left to vary the volume, or to the
right to vary the panning.
5 REVERB REVERB TIME (tiM) REVERB TYPE (rM1–HL2) 3 BALANCE (bAL)
Adds reverberation to the
sound.
Adjusts the reverb time. Selects the type of reverb.
ROOM 1 (rM1):
Short, high-density reverber-
ation.
ROOM2 (rM2):
Short, low-density reverbera-
tion.
STAGE1 (St1):
More late reverberation.
STAGE2 (St2):
More early reflections.
HALL1 (HL1):
Clear reverberation.
HALL2 (HL2):
Rich reverberation.
Adjusts the volume balance be-
tween the direct sound and ef-
fect sound.
6 TAPE ECHO RATE (rAt) INTENSITY (int)
✩
BALANCE (bAL)
Simulates a tape-type echo
unit of the past.
Specifies the tape speed. Specifies the amount of echo re-
peat.
Adjusts the volume balance be-
tween the direct sound and ef-
fect sound.
7 CHORUS DEPTH (dPt) RATE (rAt) BALANCE (bAL)
Adds spaciousness and rich-
ness to the sound.
Adjusts the depth of modula-
tion.
Adjusts the rate of modulation. Adjusts the volume balance be-
tween the direct sound and ef-
fect sound.
8 FILTER+DRIVE CUTOFF (CoF) RESONANCE (rES)
✩
DRIVE (drV)
✩
A low-pass filter with over-
drive. It cuts the high frequen-
cies and adds distortion.
Adjusts the frequency that will
be cut.
Adjusts peak frequency re-
sponse at the cutoff frequency.
Adds distortion.
9 DISTORTION DRIVE (drV)
✩
TONE (ton)
✩
LEVEL (LEV)
✩
Intensely distorts the sound.
Adjusts the degree of distortion. Adjusts the tone. Adjusts the volume.
10 OVERDRIVE DRIVE (drV)
✩
TONE (ton)
✩
LEVEL (LEV)
✩
Mildly distorts the sound.
Adjusts the degree of distortion. Adjusts the tone. Adjusts the volume.
11 FUZZ DRIVE (drV)
✩
TONE (ton)
✩
LEVEL (LEV)
✩
Adds overtones and intense-
ly distorts the sound.
Adjusts the degree of distortion. Adjusts the tone. Adjusts the volume.
12 OCTAVE -2OCT LEVEL (oC2) -1OCT LEVEL (oC1) DIRECT LEVEL (dir)
Adds a pitch at lower oc-
taves.
Adds a pitch two octaves be-
low.
Adds a pitch one octave below. Adjusts the volume of the direct
sound.
SP-555_e.book 55 ページ ２００７年６月２５日 月曜日 午前９時９分