Filter
Top Products
Appendix
ZOOM HD8/HD16
182
Parameter description
Table 5
ZNR module
Parameter description
Volume Pedal module
Parameter description
Parameter name Setting range Description
Depth
Exciter: 0 – 30 Adjusts effect depth.
Others: 0 – 100 Adjusts modulation depth.
Rate
Chorus, Ensemble: 1 – 50 Adjusts modulation rate.
Flanger, Vibe, Step: 0 – 50
Adjusts modulation rate. Using rhythm tempo as reference, setting in note units is also
possible.
e
(P 180 Table 1)
Tone
0 – 10 Adjusts tonal quality.
Mix
0 – 100 Adjusts mix ratio of effect sound to original sound.
Resonance
Flanger: -10 – 10 Adjusts resonance intensity. Negative values result in reversed phase of effect sound.
Step, Cry: 0 – 10 Adjusts effect intensity.
Manual
0 – 100 Adjusts frequency range of effect.
Shift
-12 – 12, 24 Adjusts pitch shift amount in semitone units.
Fine
-25 – 25 Adjusts pitch shift amount in cent (1/100 semitone) units.
Balance
0 – 100 Adjusts balance between original sound and effect sound.
Shape
0 – 10 Adjusts effect sound envelope.
Range
1 – 10 Adjusts frequency range of effect.
Sense
-10 – -1, 1 – 10 Adjusts effect sensitivity.
Frequency
1 – 5 Adjusts frequency of effect.
Low Boost
0 – 10 Adjusts low frequency boost.
Size
1 – 100 Adjusts size of simulated space.
Reflex
0 – 10 Adjusts amount of wall reflections.
Time
Wide: 1 – 64
Adjusts delay time.Delay, Analog Delay: 1 – 2000ms
e
Reverse Delay: 10 – 1000ms
e
Wet Level
0 – 30 Adjusts effect sound level.
Dry Level
0 – 30 Adjusts original sound level.
Feedback
0 – 100 Adjusts feedback amount.
Hi Damp
0 – 10 Adjusts intensity of delay sound high range damping.
Type
Table 5 Selects pitch change type.
RTM Wave
Table 3, page 180 Selects control waveform.
RTM Sync
Table 4, page 180 Selects control waveform cycle.
Setting value Description Setting value Description
1
1 semitone lower → original sound
9
1 octave lower + original sound → 1 octave higher + original sound
2
Original sound → 1 semitone lower
10
1 octave higher + original sound → 1 octave lower + original sound
3
Doubling → detune + original sound
11
Complete fifth down + original sound → complete fourth up + original sound
4
Detune + original sound → doubling
12
Complete fourth up + original sound → complete fifth down + original sound
5
Original sound → 1 octave higher
13
0 Hz + original sound → 1 octave up
6
1 octave higher → original sound
14
1 octave up → 0 Hz + original sound
7
Original sound → 2 octaves lower
15
0 Hz + original sound → 1 octave up + original sound
8
2 octaves lower → original sound
16
1 octave up + original sound → 0 Hz + original sound
Type Parameter
ZNR
Threshold
ZOOM original noise reduction for reducing noise in playing pauses without affecting the overall tone.
Parameter name Setting range Description
Threshold
Off, 1 – 30
Adjusts ZNR sensitivity. For maximum noise reduction, set value as high as possible
without causing the sound to decay unnaturally.
Type Parameter
Volume Pedal
Min Volume
Allows volume adjustment with the expression pedal.
Parameter name Setting range Description
Min Volume
0 – 10 Adjusts the minimum volume when using the expression pedal for volume control.