Chapter 7. IBM iSeries 820, 830, and 840 features and placement 227
#0142
(cont.)
#0142 Linux Partition Specify
See the descriptions of the individual feature to understand the capabilities and PCI slot limitations of the features attached
directly to Linux partitions.
Linux direct attach features do not use or require PCI IOPs. They are only supported in a secondary LPAR partition and
require OS/400 V5R1 or later running in the primary partition.
Corequisite: #0140 Logical Partition Specify.
Maximum: Up to one less than the total number of partitions allowed on system/processor.
Linux partitions are supported with SUSE Linux Enterprise Server 9 for POWER™ or Red Hat Enterprise Linux AS for
POWER Version 3.
AIX partitions are supported with AIX 5L™ for POWER V5.2.
Minimum operating system level: OS/400 V5R1
Supported on Models 820, 830, 840
#0205 #0205 RISC-to-RISC Data Migration
Specify code is used when a client orders a new (RISC) iSeries server to replace an existing AS/400e RISC-based system.
The #0205 is ordered on the initial order of a Model 820, 830, 840.
Manufacturing loads only the System Licensed Internal Code (SLIC) up through QSYS of OS/400 when the #0205 is
ordered. Because of this limited loading of OS/400 by manufacturing, #5000 Software Preload Required is not allowed with
the #0205. The #0205 RISC-to-RISC Data Migration and #5000 Software Preload Required are mutually exclusive.
#0272
#0272 Renovated by IBM
The #0272 Renovated by IBM feature is a specify code used to indicate that the system is to be built from new or refurbished
parts.
Supported on Models 820, 830, 840
#0299 #0299 MES Conversion Analysis for #5580/5581 MES
The #0299 provides additional ordering/scheduling steps for Customers adding Auxiliary Write Cache IOA to existing large
cache disk controllers (converting #2757, #2780, to #5580, #5581).
The marketing configurator adds no-charge #0299 feature to order to indicate a conversion.
Automated tool analyzes current MRPD configuration to determine if simple MES or potentially more complex MES.
The order is scheduled if simple MES or upon confirmation the sales team has done planning for complex MES.
Minimum operating system level: OS/400 V5R2 with CUM C5123520 and prerequisites; MF 35176, MF35006, MF34997,
M34993, MF34888,
Supported on Models 820, 830, 840.
#0382 #0382 Remote Control Panel Cable
The #0382 ships a cable to enable remote control on an Model 820, 830, or 840. This cable attaches to a PC parallel port.
An available parallel port (LPT) is needed on the PC instead of a COM port. The parallel port must be configured to use
Enhanced Parallel Port 1.9 (EPP) support, which might require a change in the PC’s Basic Input/Output Services (BIOS).
Check with your PC manufacturer for any assistance.
The Remote Control Panel is installed and used from PCs running the Windows NT 4.0 or Windows 2000 Professional PC
operating system. Some PCs might not support this function due to BIOS or hardware incompatibilities.
Supported on Models 820, 830 and 840
The #0382 is a Customer Install Feature (CIF).
The #0382 Remote Control Panel Cable was withdrawn from marketing on 12 February 2002.
#0383 #0383 Remote Control Panel Cable
The #0383 Remote Control Panel Cable provides a remote control panel parallel port cable. An available parallel port (LPT)
is needed on the PC instead of a communications port. This port must be configured to use Enhanced Parallel Port 1.9
(EPP) support, which might require a change in the PC’s BIOS. It is only supported on PCs running Windows NT 4.0 or
Windows 2000 Professional, and V5R2 iSeries Access for Windows running on the Operations Console PC. iSeries Access
clients at OS/400 V5R1 can receive this by ordering the refresh of iSeries Access Family #2645. OS/400 V5R1 clients
without an iSeries Access license need to purchase one.
Supported on Models 820, 830, and 840
Minimum operating system level: OS/400 V5R1
The #0383 is a Customer Install Feature.
The #0383 was withdrawn from marketing on 01 June 2006.
