Filter
Top Products
E-200/E-100
45
Working with the Flash memory
Let us first have a look at the remaining Function parameters.
They allow you to save newly recorded songs and Styles loaded
from a floppy disk
[E-200 only]
to the E-200/E-100’s Flash mem-
ory, and to remove such files.
Saving songs to a Flash memory
Songs you record or edit with the E-200/E-100’s Recorder (or
that you modify using the Stylist functions) can be saved to its
Flash memory or floppy disk
[E-200 only]
. See page 49 for how to
save them to floppy and page 16 for how to select songs in the
Flash memory.
(1) Press [FUNCTION].
(2) Use FAMILY [√][®] to select the “WriteSNG” parameter.
Wait until the display looks as shown above, then proceed
with the following step.
The E-200/E-100 automatically selects a Flash memory that
doesn’t yet contain data. (The first character, “S”, flashes.)
Note: If no vacant Flash memory remains or if the memory
capacity is exhausted, the display shows the “Mem Full”
message when you select this function. In that case, it will be
impossible to save your song. You can, however, delete another
song (“Remove”) and repeat step (2) and following.
Note: The “No Song” message means that there are no song
data that could be saved.
(3) If necessary, use the SELECT [√][®] buttons to move the
cursor to another character position (that character
flashes).
(4) Use the numeric buttons to assign a character to that
position.
The available characters are:
Note: Each time you press another numeric button (for entering
characters), the cursor advances automatically to the next posi-
tion. This works like a mobile phone.
(5) Repeat steps (3) and (4) to assign the desired characters to
the remaining positions.
(6) After entering the name, press the [YES/+] button to save
the song to the E-200/E-100’s Flash memory.
The display now counts down:
At the end of the saving operation, the display briefly shows
the “Complete” message.
Note: Press [NO/–] if you do not wish to save the song after all.
(7) Press another “big” button in the DATA ENTRY section to
leave this function.
Saving Styles to a Flash memory
[E-200 only]
Music Styles you load from floppy disk (and which are copied to
the USER STL memory at that time) can be saved to a Flash
memory.
(1) Press [FUNCTION].
(2) Use FAMILY [√][®] to select the “WriteSTL” parameter.
Wait until the display looks as follows, then proceed with the
next step:
The E-200 automatically selects a Flash destination memory
that doesn’t yet contain data. (The first character flashes.)
Note: If no vacant Flash memory remains or if the memory
capacity is exhausted, the display shows the “Mem Full”
message when you select this function. In that case, it will be
impossible to save the Music Style. You can, however, delete
another Style (“Remove”) and repeat step (2) and following.
Note: The “No Style” message means that there are no
Style data that could be saved.
(3) If necessary, use the SELECT [√][®] buttons to move the
cursor to another character position (that character
flashes).
(4) Use the numeric buttons to assign a character to that
position.
The available characters are:
(5) Repeat steps (3) and (4) to assign the desired characters to
the remaining positions.
Note: Each time you press another numeric button (for entering
characters), the cursor advances automatically to the next posi-
tion. This works like a mobile phone.
(6) After entering the name, press the [YES/+] button to save
the Style to the E-200’s Flash memory.
14. Data management
FUNCTION
=
SONG 001
yes
_ ! # $ % & ’ - @ ^ ‘
0 1 2 3 4 5 6 7 8 9
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
Writing
=
TANGO
yes
_ ! # $ % & ’ - @ ^ ‘
0 1 2 3 4 5 6 7 8 9
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
E-200_US Page 45 Tuesday, January 27, 2004 4:01 PM