Yamaha CP5 Electronic Keyboard User Manual


 
Internal Design of the CP5 & CP50
Reference
Left & Right Parts
[VOICE]
[PRE-AMP]
[MOD-FX]
[PWR-AMP] (CP5 only)
[LEFT1]/[LEFT2]/[RIGHT1]/
[RIGHT2] (CP5)
[LEFT]/[RIGHT] (CP50)
[COMMON]
Song Setting Area
[SONG SETTING]
[RECORD]
TRACK Part
[TRACK]
MIC INPUT Part
[MIC INPUT] (CP5 only)
Settings for All Parts
[REVERB]
Settings for All Performances
[MASTER COMPRESSOR]
[UTILITY]
[FILE]
Appendix
40 CP5/CP50 Reference Manual
MIC INPUT Part (CP5 only)
This section provides a detailed description of the parameters used to configure the CP5’s MIC
INPUT part. The setting screen for this part contains two pages.
Mic Effects Screen
From the Mic Effects screen, you can set parameters affecting the compressor, noise gate, and EQ
that act on audio signals input via the MIC INPUT jack. This screen contains a total of seven pages.
Edit Sequence
Press and hold the [MIC INPUT] button (for at least one second) Navigate to the
required page using the [ PAGE] and [PAGE ] buttons Turn or press Knobs 1 to 3
Page
On-screen name
(and full name)
Description
1 Volume This parameter is used to adjust the part’s output level. It can also be set at any
time using the [MIC INPUT] knob on the control panel.
Setting values: 0 to 127
Pan This parameter is used to adjust the part’s stereo panning.
Setting values: L63 (far left) to C (center) to R63 (far right)
RevSend (Reverb
Send)
This parameter is used to set how much of the part’s output signal is sent to the
Reverb block. Higher values produce a more pronounced reverb sound.
Setting values: 0 to 127
2 MicFx (Mic Effects) By pressing Knob 1 on this page, you can open the Mic Effects screen (see
below) in order to configure the compressor, noise gate, and EQ that act on the
microphone input.
MicIns (Mic Insert
Effect)
By pressing Knob 2 on this page, you can open the Mic Insert Effect screen
(page 41) in order to select and configure an insertion effect for the microphone
input.
Edit Sequence
Press and hold the [MIC INPUT] button (for at least one second) Navigate to Page 2
using the [PAGE ] button Press Knob 1 Navigate to the required page using the
[
PAGE] and [PAGE ] buttons Turn Knobs 1 to 3
Page
On-screen name
(and full name)
Description
1 NoiseSw
(Noise Gate Switch)
This parameter is used to turn on or off the noise gate for microphone input signals.
Setting values: on or off
CompSw
(Compressor Switch)
This parameter is used to turn on or off the compression of microphone input sig-
nals.
Setting values: on or off
2 NoisAtk
(Noise Gate Attack)
This parameter is used to set the amount of time that elapses between arrival of an
input signal and activation of the noise gate.
Setting values: 1ms to 40ms
NoisRel
(Noise Gate
Release)
This parameter is used to set the amount of time over which the noise gate stops
silencing the input signal.
Setting values: 10ms to 680ms
NoisTh
(Noise Threshold)
This parameter is used to set the level at which the noise gate starts silencing the
input signal.
Setting values: -73dB to -30dB
3 CompAtk
(Compressor Attack)
This parameter is used to set the amount of time that elapses between arrival of an
input signal and activation of the compressor.
Setting values: 1ms to 40ms
CompRel
(Compressor
Release)
This parameter is used to set the amount of time over which the compressor stops
compressing the sound.
Setting values: 10ms to 680ms