Filter
Top Products
COMBI P4: Zone/Delay 3–7: Other T01-08, 3–8: Other T09-16
55
of the RADIAS program used by the timbre. However, a
RADIAS program cannot be detuned farther than +/-50
cents. Values below -50 are treated as -50, and values above
+50 are treated as +50.
For more information, please see “Detune (Use BPM Adjust
in Menu)” on page 151 of the M3 parameter guide.
Bend Range [PRG, –24...+00...+24]
Specifies the amount of pitch change that will occur when
the pitch bender is operated, in semitone units.
PRG: The pitch range specified by the program will be used.
–24…+24: This setting will be used regardless of the setting
in the program.
The actual bend range is determined by adding this value to
the Bend Range (Program 2-2a) of the RADIAS program
used by the timbre. However, a RADIAS program cannot
have a bend range greater than +/-12. Values below -12 are
treated as -12, and values above +12 are treated as +12.
Timbre 02...08, 09...16 (Timbre Number):
Here you can make pitch-related settings for each timbre 2–
16. The settings are the same as for timbre 1. See “Timbre 01
(Timbre Number)”:.
3–7: Other T01-08,
3–8: Other T09-16
3–7(8)c: KARMA/Scale
Timbre 01…16 (Timbre Number):
KARMA Timbre Off Control
[Normal, Timbre Off by KARMA Off, Timbre Off by
KARMA On]
Use Program’s Scale [Off, On]
For details on these parameters, please see “3–7(8)c:
KARMA/Scale” on page 152 of the M3 parameter guide.
Scale:
Specifies the scale that the combination will use.
Type (Combi’s Scale)
[Equal Temperament…User Octave Scale15]
Selects the scale.
If you select a scale that cannot be specified for a
RADIAS program, such as Stretch, User All Notes
Scale, or User Octave Scale 01–15, the program will play
using Equal Temperament.
Key [C…B]
Random [0…7]
For more information, please see “3–7(8)c: KARMA/Scale”
on page 152 of the M3 parameter guide.
COMBI P4: Zone/Delay
Here you can specify the key range and velocity range for
which timbres 1–8 and 9–16 will sound, and specify the
delay time until the sound will be heard.
For details on the available parameters and menu
commands, please see “COMBI P4: Zone/Delay” on page
153 of the M3 parameter guide.
The Keyboard Zones / Velocity Zones “Top Slope” and
“Bottom Slope” settings will have no effect for RADIAS
program.
COMBI P5: MIDI Filter
These settings allow you to apply filters to the MIDI data
that will be transmitted and received by each timbre 1–16.
For details on the available parameters and menu
commands, please see “COMBI P5: MIDI Filter” on page 157
of the M3 parameter guide.
COMBI P7: KARMA
Here you can make KARMA function settings for the
Combination mode.
For details on the available parameters and menu
commands, please see “COMBI P7: KARMA” on page 161 of
the M3 parameter guide.
COMBI P8: IFX (Insert Effects)
Here you can specify the bus and insert effect for timbres 1–
16.
For details on the available parameters and menu
commands, please see “COMBI P8: IFX (Insert Effect)” on
page 177 of the M3 parameter guide.
COMBI P9: MFX/TFX
(Master/Total Effects)
Here you can make settings for the master effects and total
effects.
For details on the available parameters and menu
commands, please see “COMBI P9: MFX/TFX (Master/
Total Effect)” on page 183 of the M3 parameter guide.
3–3c