Filter
Top Products
23
padKONTROL Owner’s Manual
Disable ( )
No MIDI message will be transmitted.
3 If you want to set another parameter, skip this step.
If you are done, press the [SETTING/ENTER] key.
The setting will be applied, and you will return to Play mode.
■ Switch Type
1 Press the [SW TYPE/POLARITY] key.
The [SW TYPE/POLARITY] key will light, and the display
will indicate the sensitivity type.
2 Use the encoder to specify the switch type.
Momentary (
)
A Note-on message will be sent when you press the pedal,
and a Note-off message will be sent when you release it.
Toggle ( )
A Note-on message or a Note-off message will be sent
alternately when you press the pedal.
3 If you want to set another parameter, skip this step.
If you are done, press the [SETTING/ENTER] key.
The setting will be applied, and you will return to Play mode.
■ Release Value
If the pedal is assigned to a note number, no setting is ac-
cessed by pressing the [REL. VAL./LOWER] key. If you press
this key, the display will indicate “ ”.
■ Velocity
1 Press the [PEDAL] key.
The [PEDAL] key will light.
2 Press the [VELOCITY/UPPER] key.
The [VELOCITY/UPPER] key will light, and the display will
indicate the velocity value.
3 Use the encoder to specify a velocity value.
Velocity [1...127]
4 If you want to set another parameter, skip this step.
If you are done, press the [SETTING/ENTER] key.
The setting will be applied, and you will return to Play mode.
■ USB-MIDI Port
You can choose the USB-MIDI port to which the message will
be transmitted when you operate the pedal. This applies only if
the padKONTROL is connected via USB.
If the padKONTROL is connected via the MIDI connectors, this Port
setting does nothing. All MIDI messages will be transmitted from
the MIDI OUT connector.
1 Press the [PORT] key.
The [PORT] key will light, and the display will indicate the
USB-MIDI transmit port.
2 Use the encoder to select the USB-MIDI transmit port.
USB Port A (
)
The MIDI message assigned to the pedal will be sent to
port A.
USB Port B ( )
The MIDI message assigned to the pedal will be sent to
port B.
3 If you want to set another parameter, skip this step.
If you are done, press the [SETTING/ENTER] key.
The setting will be applied, and you will return to Play mode.
Assigning a Control Change to the pedal
You can specify the control change number, MIDI transmit chan-
nel, switch type, on-value, and release value of the control
change message that is sent when you operate the pedal.
If you want to keep the changes you made, you must save them. If
you turn off the power or switch to a different scene before saving,
your changes will be lost. (p.15 “Saving a scene”)
1 Press the [PEDAL] key.
The pedal setting will be selected, and the [PEDAL] key
will light.
■ Control Change Number
1 Press the [NOTE/CC#/LEFT] key.
The [NOTE/CC#/LEFT] key will light, and the display will
indicate the control change number.
If a note message is assigned to the pedal, the display will
indicate the note number.
2 Use the encoder to specify the control change number.
Control Change Number [0...127]
(p.115 “MIDI Control Change Messages”)
3 If you want to set another parameter, skip this step.
If you are done, press the [SETTING/ENTER] key.
The setting will be applied, and you will return to Play mode.
■ MIDI Channel
You can specify the MIDI channel on which the control change
message will be sent when you operate the pedal.
For the procedure, refer to p.20 “MIDI Channel”.
■ Switch Type
You can specify the type of switch operation that will occur
when you operate the pedal.
For the procedure, refer to p.20 “Switch Type”.
■ On Value
This parameter specifies the On Value (control change value)
that is sent when you press the pedal.
1 Press the [VELOCITY/UPPER] key.
The [VELOCITY/UPPER] key will light, and the display will
indicate the On Value (control change value) that is trans-
mitted when you press the pedal.
If a note message is assigned to the pedal, the display will
indicate the velocity value.