Filter
Top Products
106
Chapter 8 Parameters Guide COSM BASS
PITCH
*1 Setting available with SHIFT MODE set to HARMO.
*2 Setting available with SHIFT MODE set to SHIFT.
*3 Setting available with HARMO set to USER.
*4 Setting available when MODLNG TYPE for COSM BASS is set
to E.BASS, AC BASS, or SYNTH.
*5 Setting available when MODLNG TYPE for COSM BASS is set
to E.GTR.
* When ANALOG GR has been selected for COSM BASS, using
SHIFT, HARMO, or BEND to make settings that shift the pitch in an
extreme way may make sound generation unstable.
Creating Harmony Scales (User Harmony)
When HARMO is set to any value from -2oct to +2oct, and the
harmony does not sound the way you intend, use a User harmony.
You can set the corresponding pitches to be output for each input
pitch.
1.
Set HARMO to USER in the Harmony screen.
2.
Press PAGE [ ] .
The User Harmony screen appears.
fig.04-0100d
3.
Use PAGE [ ] [ ], [F1]–[F6], and the F1–F6 knob to set
the amount of pitch shift for each voice.
Parameter/
Range
Explanation
PITCH SHIFT (Pitch Shift)
OFF, ON
Turns pitch shift on/off.
SHIFT MODE (Pitch Shift Mode)
Selects the operation of pitch shift.
SHIFT This lets you fine tune the setting for the
fixed amount of pitch shift.
HARMO This analyzes the pitch of the bass input and
automatically adjusts the amount of pitch
shift. You can use this to create diatonic-
scale harmonies.
KEY *1
C Am–B G#m
Specify the key of the song you are playing.
This KEY parameter is the same as the Key
setting in the [NAME/KEY/BPM] section
(p. 142) and FX MOD1, 2 HARMONIST.
Altering either one changes the key.
HARMO (Harmony) *1
-2oct–TONIC–+2oct,
USER
This sets the pitch for the harmony interval rel-
ative to the input sound.
When this is set to USER, you can set this to the
desired harmony in USER INTERVAL.
BEND
0–100
Setting this to 0 makes for no shift in pitch
by bend, and setting it to 100 produces shift-
ing according to the settings for HiC, 1st
through 4th, LowB.
Normally, you can use the unit with BEND
for patches set at 0 and use Control Assign
to adjust the bend setting between 0 and
100.
* This setting cannot be saved with the patch.
Switching patches resets the setting to 0.
SHIFT HiC, 1–4th, LowB *2
-24–+24
This sets the amount of pitch shift for each
individual string, in semitone steps.
FINE HiC, 1–4th, LowB *2
-50–+50
This fine tunes the amount of change in the
pitch shift sound for each individual string.
USER HARMONY C–B *3
-24–+24
This sets the output pitch relative to the in-
put pitch for the selected key.
BEND SHIFT HiC, 1–4th, LowB
-24–+24
This sets the amount of pitch shift in each
string when the BEND is set to 100.
The amount of shift from the current pitch is
set in semitone increments.
DELAY HiC, 1–4th, LowB
0–100ms
This adjusts the delay of the pitch-shift
sound for each individual string.
EFFECT LEVEL HiC, 1–4th, LowB *4
0–100
Adjusts the volume of the pitch shift sound
for each string.
DIRECT LEVEL HiC, 1–4th, LowB *4
0–100
Adjusts the volume of the direct sound for
each string.
LEVEL HiC, 1–4th, LowB *5
0–100
Adjusts the volume of the pitch shift sound
for each string.
Parameter/
Range
Explanation
VB-99_e.book 106 ページ ２００８年８月１８日 月曜日 午後１時１０分