Filter
Top Products
154
Chapter 8 Parameter Guide SYSTEM
FC-300 CTL6
FC-300 external footswitch6
FC-300 E5/C7 FC-300 external expression pedal5/external
footswitch7
FC-300 CTL8 FC-300 external footswitch8
INTRNL PEDAL Internal pedal
WAVE PEDAL Wave pedal
TARGET
Used in the general V-LINK compatible device.
DISLV CC #5 Dissolve time
(time elapsed in switching video images)
Cb CC #74 Color cb (Color difference signal)
Cr CC #71 Color cr (Color difference signal)
Used in the motion dive .tokyo performance package.
COLOR EQ-FG Color foreground
COLOR EQ-BG Color background
SCRTCH SW Scratch switch
SPEED KNOB Speed knob
TOTAL FADER Total fader
CROSS FADER Cross fader
BPM SYNC BPM sync switch
CLIP LOOP Clip loop switch
ASSIGN KNOB Assignable knob
FADE TIME Fade time switch
VISUAL KNOB Visual plug-in control knob
AB SW A/B switch
TAP SW Tap switch
TOTAL SELECT Total select
FX SELECT Effect select
PLAY POS Play position
LOOP START Loop start position
LOOP END Loop end position
LAYER MODE Layer mode select
DV-7PR
PLAY SPEED Play speed
DISLV TIME Dissolve time
(time elapsed in switching video images)
T BAR T bar
COLOR Cb Color cb (Color difference signal)
COLOR Cr Color cr (Color difference signal)
BRIGHTNESS Brightness
VFX 1 Visual effects1
VFX 2 Visual effects2
VFX 3 Visual effects3
VFX 4 Visual effects4
OUTPUT FADE Output fade
DUAL STREAM Dual stream
MIN (Minimum) *1
0–127 Sets the lower limit in the range the param-
eter changes.
MAX (Maximum) *1
0–127
Sets the upper limit in the range the param-
eter changes.
Parameter/
Range
Explanation
Parameter/
Range
Explanation
TRIGGR (Trigger) *2
Sets the point at which the virtual expression pedal’s action begins.
PATCH CHANGE Functions when patches are switched.
GK VOL Functions when the divided pickup’s vol-
ume knob is adjusted.
GK S1, S2 Functions when the divided pickup’s
DOWN/S1 or UP/S2 switch position is
changed.
CTL1–CTL4 Functions when the CTL 1, 2 buttons or foot
switch connected to CTL 3,4 jack are operat-
ed.
EXP PEDAL Functions when the expression pedal con-
nected to EXP PEDAL jack are operated.
D BEAM V, H Functions when the vertical or horizontal
position is detected by the D Beam control-
ler.
RIBBON ACT, POS Functions when the ribbon controller is op-
erated by touch or when the position is de-
tected.
FC-300 EXP1, EXP2 Functions when the FC-300’s EXP PEDAL 1
or 2 is operated.
FC-300 CTL1, CTL2 Functions when the FC-300’s CTL1 or CTL2
is operated.
FC-300 E3/C3, CTL4,
E4/C5, CTL6, E5/C7,
CTL8
Functions when a pedal connected to the
FC-300’s E3/C3, CTL4, E4/C5, CTL6, E5/
C7, or CTL8 jacks is operated.
TIME *2
0–100 Adjusts the amount of time for the virtual
expression pedal to shift from the fully re-
leased position (pedal toe raised) to the fully
depressed position (pedal toe pressed
down).
CURVE *2
This selects one of the three types that determines how the assumed
expression pedal changes.
RATE *3
0–100
This determines the time spend for one cycle
of the assumed expression pedal.
FORM *3
This selects one of the three types that determines how the assumed
expression pedal should change.
LINEAR SLOW RISE FAST RISE
SAW
TRI
SIN
VB-99_e.book 154 ページ ２００８年８月１８日 月曜日 午後１時１０分