Filter
Top Products
97
Multi-Effects List
Effects
19: SPACE-D
This is a multiple chorus that applies two-phase modulation in
stereo. It creates no audible modulation, yet produces a transparent
chorus effect.
fig.MFX19
20: STEREO CHORUS
This is a stereo chorus. A filter is provided so that you can adjust the
timbre of the chorused sound.
fig.MFX20
21: STEREO FLANGER
This is a stereo flanger. It produces a metallic resonance that rises
and falls somewhat like a jet airplane taking off or landing. A filter is
provided so that you can adjust the timbre of the flanged sound.
fig.MFX21
Parameter
Value Description
Pre Delay
0.0–100.0
ms
Adjusts the time until the chorus
sound is heard.
Rate #1 0.05–10.00
Hz
Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180 deg Spatial spread of the sound
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Balance #2 D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the chorus sound
(W)
Level 0–127 Output level
Parameter
Value Description
Filter Type
OFF, LPF,
HPF
Type of filter
OFF:
no filter is used
LPF:
cuts the frequency range
above the Cutoff Freq
HPF:
cuts the frequency range
below the Cutoff Freq
Cutoff Freq 200–8000
Hz
Basic frequency of the filter
Pre Delay 0.0–100.0
ms
Adjusts the time until the chorus
sound is heard.
Rate #1 0.05–10.00
Hz
Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180 deg Spatial spread of the sound
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Balance #2 D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the chorus sound
(W)
Level 0–127 Output level
L in
R in
Space D
Space D
L out
R out
2-Band
EQ
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
L in
R in
Chorus
Chorus
L out
R out
2-Band
EQ
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
Parameter
Value Description
Filter Type
OFF, LPF,
HPF
Type of filter
OFF:
no filter is used
LPF:
cuts the frequency range
above the Cutoff Freq
HPF:
cuts the frequency range
below the Cutoff Freq
Cutoff Freq 200–8000
Hz
Basic frequency of the filter
Pre Delay 0.0–100.0
ms
Adjusts the time until the flanger
sound is heard.
Rate #1 0.05-10.00
Hz, note
Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180 deg Spatial spread of the sound
Feedback
#2
-98– +98 % Adjusts the amount of the flanger
sound that’s fed back into the effect.
Negative (-) settings invert the
phase.
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Balance D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the flanger sound
(W)
Level 0–127 Output level
R in
R out
L in
L out
Flanger
Feedback
Feedback
Flanger
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
MC-909_Ref_e.book 97 ページ ２００５年３月１日 火曜日 午後３時２９分