Filter
Top Products
®
11. Utility parameters (Advanced)
100
r
FR-7x V-Accordion
(1) Press the [DATA÷ENTER] knob to select the “TYPE”
field.
(2) Rotate the [DATA÷ENTER] knob to select the set-
tings you want to restore:
(3) Press the [DATA÷ENTER] knob to confirm your set-
tings.
(4) Press the [MENU÷WRITE] button to copy the set-
tings.
The display confirms this operation.
11.9 FR-7/5 Import
This function allows you to
load MIDI bulk data of an
FR-7/5 V-Accordion from a
USB storage device. You
therefore first need to copy
the file in question to a USB storage on your computer.
Parameters that don’t exist on the FR-7/5 are reset to
their factory defaults (on the FR-7x), and Sets 41~80 are
left untouched (the FR-7/5 only has 40 Set memories).
(1) Connect a USB storage device to the FR-7x’s USB
port.
(2) Press the [DATA÷ENTER] knob to select the “FILE”
field.
(3) Press the [DATA÷ENTER] knob to select the file
whose bulk settings you want to load.
To open an existing folder, select it by rotating the
[DATA÷ENTER] knob, then press the [DATA÷ENTER]
knob. You can also select the “(level up)” entry and
press the [DATA÷ENTER] knob to return to a higher
level (i.e. leave the current folder).
(4) Rotate the [DATA÷ENTER] knob to select a file and
press it to confirm.
The “IMPORT” field is now selected.
(5) Press the [DATA÷ENTER] knob to import the set-
tings.
(6) Press the [MENU÷WRITE] button to load the set-
tings.
After an “Executing… Do NOTE Power Off” message,
the display shows “Function Complete”.
11.10 Treble Reg. on current Set
This is an environment in its
own right rather than a
parameter. It allows you to set
five parameters for all Treble
registers of the currently
selected Set simultaneously. This may help you save a lot
of time, especially for increasing or decreasing the vol-
ume of some or all reeds, or for selecting a different
noise type.
(1) Select the Set whose Treble registers you want to
edit simultaneously.
(2) Press the [DATA÷ENTER] knob and rotate it to select
the parameter to be edited for all Treble registers.
The possibilities are:
Reed: Reed ALL, Reed 16’, Reed 8’, Reed 8'–, Reed 8'+,
Reed 4', Reed 5-1/3’, Reed 2-2/3’
Volume: Vol ALL, Vol 16’, Vol 8’, Vol 8'–, Vol 8'+,
Vol 4', Vol 5-1/3’, Vol 2-2/3’
Others: Noise, Noise Vol, MusDetune
If you selected “Reed ALL” or “Vol ALL”, the following
warning may be displayed:
This only occurs if the “VALUE” next to it is currently
“---”, which means that the reeds of your Set use dif-
ferent settings. By proceeding with “ALL”, you would
assign the same value to all registers of the current
Set.
(a) Press the [DATA÷ENTER] knob to set the same value
for all reeds.
(b) Press the [EXIT÷JUMP] button to stop the operation.
(3) Press the [DATA÷ENTER] knob to select “VALUE”,
then rotate the [DATA÷ENTER] knob to select the
desired setting.
Setting Meaning
ALL Restores all of the FR-7x’s settings.
Master Tune Restores the last “1.1 Master Tune” setting
you saved (page 64).
Scale Tune Restores the last “1.4 Scale Edit” (page 64)
and “1.5 Scale Assign” settings you saved
(page 65).
System Restores the last “10. System” settings you
saved (page 86).
MIDI Restores the last “12. MIDI” settings you
saved (page 107).
All Sets Restores the settings of all Sets and the
registers they contain.
Set 1~80 Restores the settings of the selected Set.
FR-7x GB.book Page 100 Tuesday, August 25, 2009 10:58 AM