Filter
Top Products
Overdrive
V-Accordion
r
55
(3) Rotate the [DATA÷ENTER] knob to select one of the
following parameters:
(4) Press the [DATA÷ENTER] knob to confirm your
selection.
(5) Rotate the [DATA÷ENTER] knob to set the desired
value.
(6) Press the [DATA÷ENTER] knob to confirm your set-
ting.
(7) Repeat steps (2)~(6) to set the remaining parame-
ters.
Note: See “Saving your settings” on p. 52 for how to save
your settings if you are happy with the organ sound. Oth-
erwise continue with the next section.
Overdrive
This effect distorts the sound, giving it an “edge” and
making it suitable for hard rock and similar musical
genres. See also important remark under “Vibrato/Cho-
rus”.
(1) Select the “Overdrive” page.
See “Editing the selected organ sound” on p. 53.
(2) Press the [DATA÷ENTER] knob to select the
“PARAM” parameter.
(3) Rotate the [DATA÷ENTER] knob to select one of the
following parameters:
(4) Confirm your setting by pressing the [DATA÷ENTER]
knob.
(5) Rotate the [DATA÷ENTER] knob to set the desired
value.
(6) Confirm your setting by pressing the [DATA÷ENTER]
knob.
(7) Repeat steps (2)~(6) to set the remaining parame-
ters.
Note: See “Saving your settings” on p. 52 for how to save
your settings if you are happy with the organ sound. Oth-
erwise continue with the next section.
Rotary
The effect in this section simulates the typical sound
modulation generated by a cabinet with rotating loud-
speakers.
Most functions (start/stop, rotation speed selection,
etc.), need to be selected with a footswitch. See page 87
for how to define those functions.
(1) Select the “Rotary” page.
See “Editing the selected organ sound” on p. 53.
(2) Press the [DATA÷ENTER] knob to select the
“PARAM” parameter.
(3) Rotate the [DATA÷ENTER] knob to select one of the
following parameters:
Parameter Description
Switch Allows you to switch the effect on or off.
Setting range: Off, On
Type V-1, V-2, V-3: This applies vibrato (pitch
modulation). Increasing the value will pro-
duce a deeper effect.
C-1, C-2, C-3: This applies chorus to add
depth and spaciousness to the sound.
Increasing the value will produce a deeper
effect.
Vintage Allows you to choose the sound of the
selected effect. The settings recreate pop-
ular sounds in different periods.
Setting range: ‘50s, ‘60s, ‘70s
Level Specifies the level of the effect with
respect to the unprocessed organ signal.
Setting range: 0~127
Parameter Description
Switch Allows you to switch the overdrive effect
on or off.
Setting range: Off, On
Drive Specifies how strongly the sound is dis-
torted.
Setting range: 0~127
Level Specifies the level of the effect with
respect to the unprocessed organ signal.
Setting range: 0~127
Parameter Description
Level Specifies the level of the Rotary effect
with respect to the unprocessed organ
signal.
Setting range: 0~127
Send Rev.* Allows yo to specify the level of the rotary
signal that is transmitted to the TW reverb
effect. This is not the same processor as
the one assigned to the [REVERB] knob.
Choose “0” if the sound should not be pro-
cessed by the TW reverb processor.
Setting range: 0~127
Send Cho.* Allows yo to specify the level of the rotary
signal that is transmitted to the TW cho-
rus effect. This is not the same processor
as the one assigned to the [CHORUS] knob
Choose “0” if the sound should not be pro-
cessed by the TW chorus processor.
Setting range: 0~127
Parameter Description
FR-7x GB.book Page 55 Tuesday, August 25, 2009 10:58 AM