Filter
Top Products
11.6 Import All FR-7x (Advanced)
V-Accordion
r
99
(8) Press the [DATA÷ENTER] knob twice and rotate it to
select the file name in the bottom row.
(9) Rotate the [DATA÷ENTER] knob to select the charac-
ter you want to change.
(10) Press the [DATA÷ENTER] knob.
(11) Enter the desired name for your archive.
See page 70 for how to enter names.
(12) Press [MENU÷WRITE] to archive your settings.
The display shows the following message:
(13) Press [MENU÷WRITE] again to confirm your inten-
tion.
The display confirms this operation:
If a file of the same name already exists, the follow-
ing message is displayed:
To overwrite that file, press the [MENU÷WRITE] but-
ton.
11.6 Import All FR-7x
This parameter allows you to
load all settings of the
selected FR-7x archive. Be
aware that doing so will over-
write the entire memory
contents of the FR-7x.
(1) Connect a USB storage device to the FR-7x’s USB
port.
(2) Press the [DATA÷ENTER] knob to select the “FILE”
field.
(3) Press the [DATA÷ENTER] knob to confirm the file
selection.
To open an existing folder, select it by rotating the
[DATA÷ENTER] knob, then press the [DATA÷ENTER]
knob. You can also select the “(level up)” entry and
press the [DATA÷ENTER] knob to return to a higher
level (i.e. leave the current folder).
(4) Rotate the [DATA÷ENTER] knob to select the files
and press it to confirm.
(5) Press the [DATA÷ENTER] knob to import the set-
tings.
The display shows “Press WRITE to proceed”.
(6) Press the [MENU÷WRITE] button.
After an “Executing… Do NOTE Power Off” message,
the FR-7x imports all Sets.
11.7 Import Set
This function allows you to
import the settings of a Set
file. You can choose the Set
memory the settings should
be loaded to.
Note: You cannot select single Sets of a file archived with
“11.4 Export All FR-7x” on p. 98.
(1) Connect a USB storage device to the FR-7x’s USB
port.
(2) Press the [DATA÷ENTER] knob and rotate it to select
the Set memory that should contain the Set set-
tings you are about to load.
(3) Press the [DATA÷ENTER] knob to select the “FILE”
field.
(4) Press the [DATA÷ENTER] knob to confirm the files
selection.
To open an existing folder, select it by rotating the
[DATA÷ENTER] knob, then press the [DATA÷ENTER]
knob. You can also select the “(level up)” entry and
press the [DATA÷ENTER] knob to return to a higher
level (i.e. leave the current folder).
(5) Rotate the [DATA÷ENTER] knob to select the file to
import and press it to confirm.
(6) Press the [DATA÷ENTER] knob to import the set-
tings.
The display shows the following message:
(7) Press [MENU÷WRITE] to confirm your intention.
After an “Executing… Do NOTE Power Off” message,
the FR-7x imports the selected Set.
11.8 Restore Data
(All, Master Tune, Scale Tune,
System, MIDI, All Sets, Set 1~
Set 80)
This function allows you to
undo all or some changes you
made after last saving your settings by reloading the last
version you saved. This can be handy when it turns out
that your changes don’t yield the expected result and
that starting all over again would be quicker than
changing the parameters back.
Note: This function does not necessarily load the factory set-
tings: it loads the settings stored in the selected memory
area(s).
FR-7x GB.book Page 99 Tuesday, August 25, 2009 10:58 AM