Filter
Top Products
75
6. Global mode
6. Global mode
In Global mode you can set parameters such as metronome
settings, overall tuning, memory protect, etc. To enter Global
mode, press the GLOBAL key. To exit Global mode, press
a different mode key.
If you turn off the power without writing the settings
you make in Global mode, your changes will be
discarded. If you want to keep the changes you
made, perform the Write operation (☞p.76 “Saving
your Global mode settings”).
Setting the metronome
These controls allow you to specify how the metronome will
operate. The metronome is convenient when you are using
realtime recording to create patterns.
The metronome will sound at quarter-note intervals. Except
for when you have selected the “On➝3/4” setting, the sound
of metronome is output from line out jacks L/R and from
the headphone jack, mixed with the sound of the EMX-1’s
playback and audio input.
1. Press the [
] key until the parameter display reads
“Metronom.”
2. Turn the dial to make the desired metronome set-
ting.
You cannot write the metronome setting. When the
power is turned on, it will always be “Off.”
METRONOME ..... [Off, Rec0, Rec1, Rec2, On,
On➝3/4]
Off The metronome will not sound.
Rec0 The metronome will sound only during
recording (when REC and PLAY/CAN-
CEL keys are lit)
Rec1 When you start recording, there will be a
one-measure count before recording ac-
tually begins. The metronome will sound
only during recording.
Rec2 When you start recording, there will be a
two-measure count before recording ac-
tually begins. The metronome will sound
only during recording.
On The metronome will sound during play-
back or recording. There will be no count
before recording begins.
On➝3/4 During playback or recording, the met-
ronome will be output from individual
out jacks 3/4. (The metronome will not
be output from the line out L/R jacks or
the headphone jack.) There will be no
count before recording begins.
Matching the tuning with
another instrument
You can adjust the basic tuning of the EMX-1 in steps of one
cent. Normally you will leave this set at “+00” (A=440 Hz).
Adjust this setting if you need to match the pitch of the EMX-
1 to another instrument.
Use the [ ]/[ ] cursor keys to select“MstTune” in the pa-
rameter display. Turn the dial to make the desired setting.
MASTER TUNE ............................... -50...+50
This value will be changed by MIDI Master Fine
Tune messages received from an external device.
The pitch of drum parts will not change.
Protecting the data in memory
This setting lets you protect the Pattern mode and Song mode
data.
Use the [ ]/[ ] cursor keys to select “Protect” in the pa-
rameter display. Turn the dial to select Off or On.
PROTECT........................................... Off, On
On The WRITE/RENAME key will be dis-
abled, and it will be impossible to rewrite
data or receive MIDI data dumps.
Off Edited data can be saved, and data
dumps can be received.
With the factory settings this is turned On.
The memory protect setting applies to Pattern mode, Part
Edit mode, Step Edit mode, and Song mode. However,
you can write your settings in Global mode and MIDI
mode regardless of the memory protect setting.
Exchangeing the arpeggiator
functions
This setting switch the functions of the arpeggiator slider
and ribbon controller.
1. Press the [ ] cursor until the display reads
“ArpCntrl.”
2. Turn the dial to select “Normal” or “Revers”
3. Press the Pattern key or Song key etc. to return to
the previous mode.
ARP CONTROL....................... Normal, Revers
Normal Slider: Pitch control (synth parts)
Ribbon: Gate time (synth parts) / Reso-
lution (drum parts) + Note-on
Revers Slider: Gate time (synth parts) / Resolu-
tion (drum parts)
Ribbon: Pitch control (synth parts) +
Note-on