Filter
Top Products
<PAGE 1>
SOUND:
Use the SOUND ∧ and ∨ buttons to select a sound.
• The buttons on the control panel may also be used to
select a sound.
VOLUME:
Use the VOLUME ∧ and ∨ buttons to adjust the volume
(0 to 127).
PAN:
Use the PAN
∧ and ∨ buttons to adjust the stereo balance
(L64–CENTER(CTR)-R63).
• At L64, the sound is completely to the left, at R63
completely to the right. At CENTER, the sound is at the
center. The display indicates the selected position.
• Even at the same numerical value, the stereo balance
may differ slightly depending on the sound.
SUSTAIN:
Use the
∧ and ∨ buttons to adjust the length of the sustain
(1–8). Use the ON/OFF buttons to enable or disable the
sustain effect, when the sustain pedal is depressed.
GLIDE PEDAL:
Use the GLIDE ON/OFF buttons to enable or disable the
glide effect, if it has been assigned to the pedal.
• For pedal settings, refer to page 121.
KEY SHIFT:
Use the KEY ∧ and ∨ buttons to specify the amount of
key shift (–24 to +24).
• A value of 1 means a shift of one semi-tone. To raise (or
lower) the pitch one octave, set the value to +12 (or –12).
• The ∨ button is used to lower the pitch, and the ∧ button
to raise the pitch.
TUNING:
Use the TUN ∧ and ∨ buttons to adjust the fine tuning
(–128 to +127).
• The ∨ button is used to lower the pitch, and the ∧ button
to raise the pitch.
ORIGINAL TUNING:
Use the ORIG. ON/OFF button to enable or disable the
tuning for each sound.
• For details about ORIGINAL TUNING, refer to page 107.
<PAGE 2>
REVERB:
Use the REVERB ∧ and ∨ buttons to adjust the depth
of the REVERB (0 to 127).
DIGITAL EFFECT:
Use the DIG. EFFECT ON/OFF buttons to set the DIGI-
TAL EFFECT to on or off.
CHORUS:
Use the ON/OFF button to set the CHORUS to on or off.
Use the ∧ and ∨ buttons to adjust the depth of the effect
(0 to 127).
MULTI:
Use the ON/OFF button to set the MULTI EFFECT to on
or off. Use the ∧ and ∨ buttons to adjust the depth of
the effect (0 to 127).
EQ LOW:
Use the FC, GAIN ∧ and ∨ buttons to adjust the sound
quality in the lower range.
EQ HI:
Use the FC, GAIN ∧ and ∨ buttons to adjust the sound
quality in the upper range.
<PAGE 3>
FILTER RESONANCE:
Use the RESO∧ and ∨ buttons to adjust the amount of
resonance (0 to 127).
BRIGHTNESS:
Use the BRIGHTNESS∧ and ∨ buttons to adjust the
brightness of the sound (0 to 127).
ATTACK TIME:
Use the ATTACK ∧ and ∨ buttons to specify the attack
time (0 to 127).
DECAY TIME:
Use the DECAY ∧ and ∨ buttons to specify the decay
time (0 to 127).
RELEASE TIME:
Use the RELEASE ∧ and ∨ buttons to specify the release
time (0 to 127).
VIBRATO RATE:
Use the RATE ∧ and ∨ buttons to specify the vibrato
speed (0 to 127).
VIBRATO DEPTH:
Use the DEPTH ∧ and ∨ buttons to specify the vibrato
depth (0 to 127).
VIBRATO DELAY:
Use the DELAY ∧ and ∨ buttons to specify the time in-
terval from when the keys are played until the vibrato
starts (0 to 127).
•The center value is 64 (±0).
Sound
Part VII Sound
104
QQTG0665