Filter
Top Products
Error messages
No. Contents
00
The data on the disk that you are using is for a
different product.
01
An error has occurred while the disk was loading.
Please try again!
02
There is no disk in the Disk Drive.
03
The file that you tried to load is empty.
05
An error has occurred while the disk was saving.
Please try again!
06
The disk that you are using is write protected.
Please remove the write protection and try again.
07
The disk that you are using is full. Please use
another disk.
08
An error has occurred while the disk was
formatting. The disk that you are using may be
faulty.
Please try formatting another disk.
10
The data is already copy protected.
15
The song you are trying to save is empty.
16
This STANDARD MIDI FILE is incompatible with
this instrument and cannot be loaded.
17
This is not a STANDARD MIDI FILE.
18
The timebase (PPQ resolution) that you tried to
load is not 24/48/96/192/288/384 PPQ.
20
A problem has occurred with your SEQUENCER
Data.
This might be due to a damaged or faulty disk.
21
Memory full
22
It is necessary to press REC STOP to complete
this procedure.
23
It is impossible to change the time signature
because it has already been set in the existing
tracks.
24
A rhythm track already exists. It is impossible to
assign two tracks to rhythm.
25
It is only possible to change the velocity on a
melody track.
26
It is only possible to merge melody tracks.
Tracks such as rhythm, chord and control cannot
be merged.
27
It is only possible to copy melody tracks.
Tracks such as rhythm, chord and control cannot
be copied.
28
This song is too long to be saved as a MIDI file.
29
The MIDI file that you have tried to load exceeds
the memory capacity of this instrument and cannot
be played. The SEQUENCER memory has been
cleared.
30
It is not possible to change the time signature or
measure length of a COMPOSER pattern after it
has been recorded. If you want to proceed, you
must first clear the entire COMPOSER pattern.
No. Contents
31
The time signature of the pattern from which you
are copying is different from the COMPOSER
memory that you are using.
Either: Change the time signature
of the COMPOSER memory
or: Copy from a pattern that has
the same time signature
32
Memory full
33
Select a Track before setting parameters for AUTO
PUNCH RECORD.
43
The file that you are trying to load was saved on
a previous model. It is only possible to load using
the “PERFORMANCE” option.
44
It is impossible to edit a Drum Kit. Please select
a different sound from any group except Keyboard
Percussion.
46
It is only possible to insert MELODY Tracks.
Tracks such as RHYTHM, CHORD and CONTROL
cannot be inserted.
47
This procedure is not possible with a composer
pattern or the metronome. Please select a preset
rhythm pattern.
54
It is not possible to record using preset banks,
compile banks, or control banks. Please select
one of the user banks.
55
Special tracks such as CHORD (APC), RHY and
CTL exist in the song from which you are copying
and are incompatible with the destination song
because it is in the GM mode.
56
AUTO PUNCH recording has been unsuccessful
because SEQUENCER operation was interrupted
before the PUNCH OUT measure was reached.
58
The song that you have tried to load exceeds this
instrument’s available memory and cannot be
loaded. The selected song memory has been
cleared.
62
The computer connection is not active because
the computer port switch is set to MIDI. Please
turn the power off, set the switch to the desired
setting and turn the power back on.
64
Please select the Panel Memory that you want to
name.
65
It is not possible to use the CHORD FINDER in
this mode. Please select CHORD FINDER from
HOME page or CHORD STEP RECORD page.
66
SOLO pads are special pads which include Chord
information. Pleases use SOLO pads when the
rhythm and accompaniment is playing.
67
There are no APC or CHORD tracks. Select and
APC track or CHORD track, and try again.
68
It is not possible to record directly into the SOLO
pads. Record on the SEQUENCER and Copy the
melody and chord information into a SOLO pad.
69
It is not possible to delete all measures.
70
It is not possible to insert over 16 measures in a
PATTERN.
71
It is not possible to set the start measure to the
measures you set to copy.
141
QQTG0665